AT90PWM316 Atmel Corporation, AT90PWM316 Datasheet - Page 53

• Manufacturer Part Number: AT90PWM316
• Manufacturer: Atmel Corporation

Specifications of AT90PWM316

• Flash (kbytes): 16 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 27
• Ext Interrupts: 4
• Usb Speed: No
• Usb Interface: No
• Spi: 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 11
• Adc Resolution (bits): 10
• Adc Speed (ksps): 125
• Analog Comparators: 3
• Resistive Touch Screen: No
• Dac Channels: 1
• Dac Resolution (bits): 10
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 105
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 5
• Output Compare Channels: 16
• Input Capture Channels: 1
• Pwm Channels: 12
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

9.9.1
7710F–AVR–09/11
Watchdog Timer Control Register - WDTCSR
Note:
Note: The Watchdog Timer should be reset before any change of the WDP bits, since a change
in the WDP bits can result in a time-out when switching to a shorter time-out period;
• Bit 7 - WDIF: Watchdog Interrupt Flag
This bit is set when a time-out occurs in the Watchdog Timer and the Watchdog Timer is config-
ured for interrupt. WDIF is cleared by hardware when executing the corresponding interrupt
handling vector. Alternatively, WDIF is cleared by writing a logic one to the flag. When the I-bit in
SREG and WDIE are set, the Watchdog Time-out Interrupt is executed.
Bit
Read/Write
Initial Value
Assembly Code Example
C Code Example
TABLE 2.
WDT_Prescaler_Change:
void WDT_Prescaler_Change(void)
{
}
; Turn off global interrupt
cli
; Reset Watchdog Timer
wdr
; Start timed sequence
lds r16, WDTCSR
ori
sts WDTCSR, r16
; --
; Set new prescaler(time-out) value = 64K cycles (~0.5 s)
ldi
sts WDTCSR, r16
; --
; Turn on global interrupt
sei
ret
__disable_interrupt();
__watchdog_reset();
/* Start timed
WDTCSR |= (1<<WDCE) | (1<<WDE);
/* Set new prescaler(time-out) value = 64K cycles (~0.5 s) */
WDTCSR
__enable_interrupt();
1. The example code assumes that the part specific header file is included.
r16, (1<<WDCE) | (1<<WDE)
Got four cycles to set the new values from here -
r16, (1<<WDE) | (1<<WDP2) | (1<<WDP0)
Finished setting new values, used 2 cycles -
WDIF
R/W
= (1<<WDE) | (1<<WDP2) | (1<<WDP0);
7
0
(1)
WDIE
R/W
6
0
(1)
equence */
WDP3
R/W
5
0
WDCE
R/W
4
0
WDE
R/W
X
3
WDP2
R/W
AT90PWM216/316
2
0
WDP1
R/W
1
0
WDP0
R/W
0
0
WDTCSR
53