ATmega168 Automotive Atmel Corporation, ATmega168 Automotive Datasheet - Page 25

• Manufacturer Part Number: ATmega168 Automotive
• Manufacturer: Atmel Corporation

Specifications of ATmega168 Automotive

• Flash (kbytes): 16 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 16
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 23
• Ext Interrupts: 24
• Usb Speed: No
• Usb Interface: No
• Spi: 2
• Twi (i2c): 1
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Adc Channels: 8
• Adc Resolution (bits): 10
• Adc Speed (ksps): 15
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 512
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 150
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 3
• Output Compare Channels: 6
• Input Capture Channels: 1
• Pwm Channels: 6
• 32khz Rtc: Yes
• Calibrated Rc Oscillator: Yes

6.1.4
6.1.5
6.2
6.2.1
6.2.2
7530I–AVR–02/10
Clock Sources
Asynchronous Timer Clock – clk
ADC Clock – clk
Default Clock Source
Clock Startup Sequence
The Asynchronous Timer clock allows the Asynchronous Timer/Counter to be clocked directly
from an external clock or an external 32 kHz clock crystal. The dedicated clock domain allows
using this Timer/Counter as a real-time counter even when the device is in sleep mode.
The ADC is provided with a dedicated clock domain. This allows halting the CPU and I/O clocks
in order to reduce noise generated by digital circuitry. This gives more accurate ADC conversion
results.
The device has the following clock source options, selectable by Flash Fuse bits as shown
below. The clock from the selected source is input to the AVR clock generator, and routed to the
appropriate modules.
Table 6-1.
Note:
The device is shipped with internal RC oscillator at 8.0MHz and with the fuse CKDIV8 pro-
grammed, resulting in 1.0MHz system clock. The startup time is set to maximum and time-out
period enabled. (CKSEL = "0010", SUT = "10", CKDIV8 = "0"). The default setting ensures that
all users can make their desired clock source setting using any available programming interface.
Any clock source needs a sufficient V
cycles before it can be considered stable.
To ensure sufficient V
the device reset is released by all other reset sources.
describes the start conditions for the internal reset. The delay (t
Oscillator and the number of cycles in the delay is set by the SUTx and CKSELx fuse bits. Th e
selectable delays are shown in
dependent as shown in
ADC
Device Clocking Option
Low Power Crystal Oscillator
Full Swing Crystal Oscillator
Low Frequency Crystal Oscillator
Internal 128 kHz RC Oscillator
Calibrated Internal RC Oscillator
External Clock
Reserved
1. For all fuses “1” means unprogrammed while “0” means programmed.
Device Clocking Options Select
ASY
CC
“Register Summary” on page
, the device issues an internal reset with a time-out delay (t
Table
CC
ATmega48/88/168 Automotive
6-2. The frequency of the Watchdog Oscillator is voltage
to start oscillating and a minimum number of oscillating
(1)
318.
“System Control and Reset” on page 41
TOUT
) is timed from the Watchdog
1111 - 1000
0111 - 0110
0101 - 0100
CKSEL3..0
0011
0010
0000
0001
TOUT
) after
25