ATmega32U2 Atmel Corporation, ATmega32U2 Datasheet - Page 219
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
ATmega32U2
Manufacturer Part Number
ATmega32U2
Description
Manufacturer
Atmel Corporation
Specifications of ATmega32U2
Flash (kbytes)
32 Kbytes
Pin Count
32
Max. Operating Frequency
16 MHz
Cpu
8-bit AVR
# Of Touch Channels
12
Hardware Qtouch Acquisition
No
Max I/o Pins
22
Ext Interrupts
20
Usb Transceiver
1
Usb Speed
Full Speed
Usb Interface
Device
Spi
2
Uart
1
Graphic Lcd
No
Video Decoder
No
Camera Interface
No
Analog Comparators
1
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
1
Eeprom (bytes)
1024
Self Program Memory
YES
Dram Memory
No
Nand Interface
No
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
2.7 to 5.5
Operating Voltage (vcc)
2.7 to 5.5
Fpu
No
Mpu / Mmu
no / no
Timers
2
Output Compare Channels
5
Input Capture Channels
1
Pwm Channels
4
32khz Rtc
No
Calibrated Rc Oscillator
Yes
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
- Current page: 219 of 309
- Download datasheet (6Mb)
21.18.15 UEINTX – USB Endpoint Interrupt Register
7799D–AVR–11/10
• Bit 7 – FIFOCON: FIFO Control Bit
This bit can only be written to zero by software. Writing this bit to one has no effect. The behav-
ior of this bit depends on the direction of the selected endpoint.
This flag is set by the USB controller when a new OUT message is stored in the current bank. In
this situation RXOUT or RXSTP flags are also updated at the same time. Writing this bit to zero
frees the current bank and switches to the next bank.
This flag is set by the USB controller when the current bank is free and can be loaded with never
data bytes. In this situation TXIN flag is also updated at the same time. Writing this bit to zero
sends the FIFO content and to switch the next bank.
• Bit 6 – NAKINI: NAK IN Received Interrupt Flag
This flag is set when a NAK handshake has been sent in response to a IN request from the host.
This NAKINI flag can generate a “USB endpoint interrupt” if NAKINE bit is set. Writing this bit to
zero acknowledges the interrupt source (USB clocks must be enabled before). Writing this bit to
one has no effect.
• Bit 5 – RWAL: Read/Write Allowed Flag
This flag is set by the USB controller and is relevant for all endpoint types except control end-
point. For an IN endpoint, this flag is set when the current bank is not full i.e. the firmware can
push at least one more byte into the FIFO (UPDATx register). For an OUT endpoint, this flag is
set when the current bank is not empty i.e. the firmware can read from the FIFO (UPDATx regis-
ter). When the STALLRQ bit is set or one of the endpoint error is set, this flag can not be set.
• Bit 4 – NAKOUTI: NAK OUT Received Interrupt Flag
This flag is set by the USB controller when a NAK handshake has been sent in response of a
OUT request from the host. This NAKOUTI flag can generate a “USB endpoint interrupt” if NAK-
OUTE bit is set. Writing this bit to zero acknowledges the interrupt source (USB clocks must be
enabled before). Writing this bit to one has no effect.
• Bit 3 – RXSTPI: Received SETUP Interrupt Flag
This flag is set by the USB controller when a new valid (error free) SETUP packet has been
received from the host. This RXSTPI flag can generate a “USB endpoint interrupt” if RXSTPE bit
is set. Writing this bit to zero acknowledges the interrupt source (USB clocks must be enabled
before). Writing this bit to one has no effect.
• Bit 2 – RXOUTI / KILLBK: Received OUT Data Interrupt Flag
Depending on the direction of the endpoint, this bit has two functions:
Bit
(0xE8)
Read/Write
Initial Value
• For OUT or CONTROL Endpoints:
• For IN Endpoints:
• Endpoint OUT direction (RXOUTI flag):
FIFOCON
R/W
7
0
NAKINI
R/W
6
0
RWAL
R/W
5
0
NAKOUTI
R/W
4
0
ATmega8U2/16U2/32U2
RXSTPI
R/W
3
0
RXOUTI
R/W
2
0
STALLEDI
R/W
1
0
TXINI
R/W
0
0
UEINTX
219
Related parts for ATmega32U2
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![U641B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
![U4082B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
![U4255BM-M](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B-P](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
![TDA4470](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
![ATF22V10B-25PC](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
![AT89C51ED2-IM](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
![AT24C01](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet:
![U6046B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
U6046BREAR WINDOW HEATING TIMER / LONG-TERM TIMER
Manufacturer:
ATMEL Corporation
Datasheet: