ATmega32U2 Atmel Corporation, ATmega32U2 Datasheet - Page 55

• Manufacturer Part Number: ATmega32U2
• Manufacturer: Atmel Corporation

Specifications of ATmega32U2

• Flash (kbytes): 32 Kbytes
• Pin Count: 32
• Max. Operating Frequency: 16 MHz
• Cpu: 8-bit AVR
• # Of Touch Channels: 12
• Hardware Qtouch Acquisition: No
• Max I/o Pins: 22
• Ext Interrupts: 20
• Usb Transceiver: 1
• Usb Speed: Full Speed
• Usb Interface: Device
• Spi: 2
• Uart: 1
• Graphic Lcd: No
• Video Decoder: No
• Camera Interface: No
• Analog Comparators: 1
• Resistive Touch Screen: No
• Temp. Sensor: No
• Crypto Engine: No
• Sram (kbytes): 1
• Eeprom (bytes): 1024
• Self Program Memory: YES
• Dram Memory: No
• Nand Interface: No
• Picopower: No
• Temp. Range (deg C): -40 to 85
• I/o Supply Class: 2.7 to 5.5
• Operating Voltage (vcc): 2.7 to 5.5
• Fpu: No
• Mpu / Mmu: no / no
• Timers: 2
• Output Compare Channels: 5
• Input Capture Channels: 1
• Pwm Channels: 4
• 32khz Rtc: No
• Calibrated Rc Oscillator: Yes

10.5
10.5.1
7799D–AVR–11/10
Register Description
MCUSR – MCU Status Register
Note:
Note: The Watchdog Timer should be reset before any change of the WDP bits, since a change
in the WDP bits can result in a time-out when switching to a shorter time-out period.
The MCU Status Register provides information on which reset source caused an MCU reset.
• Bit 7:6 – Res: Reserved Bit
These bits are reserved and will always read as zero.
Bit
0x34 (0x54)
Read/Write
Initial Value
Assembly Code Example
C Code Example
WDT_Prescaler_Change:
void WDT_Prescaler_Change(void)
{
}
; Turn off global interrupt
cli
; Reset Watchdog Timer
wdr
; Start timed sequence
in
ori
out
; --
; Set new prescaler(time-out) value = 64K cycles (~0.5 s)
ldi
out
; --
; Turn on global interrupt
sei
ret
__disable_interrupt();
__watchdog_reset();
/* Start timed
WDTCSR |= (1<<WDCE) | (1<<WDE);
/* Set new prescaler(time-out) value = 64K cycles (~0.5 s) */
WDTCSR
__enable_interrupt();
1. The example code assumes that the part specific header file is included.
r16, WDTCSR
r16, (1<<WDCE) | (1<<WDE)
WDTCSR, r16
Got four cycles to set the new values from here -
r16, (1<<WDE) | (1<<WDP2) | (1<<WDP0)
WDTCSR, r16
Finished setting new values, used 2 cycles -
= (1<<WDE) | (1<<WDP2) | (1<<WDP0);
R
7
–
0
(1)
(1)
R
6
–
0
equence */
USBRF
R
5
0
R/W
4
–
ATmega8U2/16U2/32U2
WDRF
R/W
3
See Bit Description
BORF
R/W
2
EXTRF
R/W
1
PORF
R/W
0
MCUSR
55