SAM9261 Atmel Corporation, SAM9261 Datasheet - Page 10
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
SAM9261
Manufacturer Part Number
SAM9261
Description
Manufacturer
Atmel Corporation
Datasheets
1.SAM9260.pdf
(290 pages)
2.SAM9261.pdf
(248 pages)
3.SAM9261.pdf
(749 pages)
4.SAM9261.pdf
(44 pages)
5.SAM9261.pdf
(1274 pages)
6.SAM9261.pdf
(43 pages)
Specifications of SAM9261
Flash (kbytes)
0 Kbytes
Pin Count
217
Max. Operating Frequency
240 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
96
Ext Interrupts
96
Usb Transceiver
3
Usb Speed
Full Speed
Usb Interface
Host, Device
Spi
2
Twi (i2c)
1
Uart
4
Ssc
3
Sd / Emmc
1
Graphic Lcd
Yes
Video Decoder
No
Camera Interface
No
Resistive Touch Screen
No
Temp. Sensor
No
Crypto Engine
No
Sram (kbytes)
160
Self Program Memory
NO
External Bus Interface
1
Dram Memory
sdram
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
1.08 to 1.32
Fpu
No
Mpu / Mmu
No/Yes
Timers
3
Output Compare Channels
3
Input Capture Channels
3
32khz Rtc
Yes
Calibrated Rc Oscillator
No
4.2.1
10
SAM9G35
Reset State
When “Reset State” is mentioned, the configuration is defined by the “Reset State” column of the
Pin Description table.
In the tables that follow, the column “Reset State” indicates the reset state of the line with
mnemonics.
Indicates whether the PIO Line resets in I/O mode or in peripheral mode. If “PIO” is mentioned,
the PIO Line is maintained in a static state as soon as the reset is released. As a result, the bit
corresponding to the PIO Line in the register PIO_PSR (Peripheral Status Register) resets low.
If a signal name is mentioned in the “Reset State” column, the PIO Line is assigned to this func-
tion and the corresponding bit in PIO_PSR resets high. This is the case of pins controlling
memories, in particular the address lines, which require the pin to be driven as soon as the reset
is released.
Indicates whether the signal is input or output state.
Indicates whether Pull-Up, Pull-Down or nothing is enabled.
Table 4-2.
• “PIO” “/” signal
• “I”/”O”
• “PU”/”PD”
GPIO_CLK2
GPIO_CLK
GPIO_ANA
RSTJTAG
EBI_CLK
I/O Type
USBFS
USBHS
CLOCK
EBI_O
SYSC
GPIO
VBG
DIB
EBI
I/O Frequency
SAM9G35 I/O Type Assignment and Frequency
(MHz)
0.25
0.25
133
133
480
40
54
75
25
66
10
12
50
25
Charge Load
50 (3.3V)
30 (1.8V)
50 (3.3V)
30 (1.8V)
(pF)
10
10
10
10
10
10
10
10
10
10
50
25
40mA (peak)
Current
Output
16mA,
all Address and control lines (output only) except the
NRST, NTRST, BMS, TCK, TDI, TMS, TDO, RTCK
HFSDPA, HFSDPB/DFSDP, HFSDPC, HFSDMA,
all Data lines (Input/output) except the following
MCI0CK, MCI1CK, SPI0SPCK, SPI1SPCK,
HHSDPA, HHSDPB/DHSDP, HHSDMA,
WKUP, SHDN, JTAGSEL, TST, SHDN
all PIO lines except the following
HFSDMB/DFSDM, HFSDMC
XIN, XOUT, XIN32, XOUT32
HHSDMB/DHSDM
EMACx_ETXCK
Signal Name
ADx, GPADx
DIBN, DIBP
following
CK, #CK
VBG
11053AS–ATARM–27-Jul-11