SAM9M11 Atmel Corporation, SAM9M11 Datasheet - Page 40
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
SAM9M11
Manufacturer Part Number
SAM9M11
Description
Manufacturer
Atmel Corporation
Specifications of SAM9M11
Flash (kbytes)
0 Kbytes
Pin Count
324
Max. Operating Frequency
400 MHz
Cpu
ARM926
Hardware Qtouch Acquisition
No
Max I/o Pins
160
Ext Interrupts
160
Usb Transceiver
3
Usb Speed
Hi-Speed
Usb Interface
Host, Device
Spi
2
Twi (i2c)
2
Uart
5
Lin
4
Ssc
2
Ethernet
1
Sd / Emmc
2
Graphic Lcd
Yes
Video Decoder
Yes
Camera Interface
Yes
Adc Channels
8
Adc Resolution (bits)
10
Adc Speed (ksps)
440
Resistive Touch Screen
Yes
Dac Resolution (bits)
No
Temp. Sensor
No
Crypto Engine
AES/DES
Sram (kbytes)
64
Self Program Memory
NO
External Bus Interface
2
Dram Memory
DDR2/LPDDR, SDRAM/LPSDR
Nand Interface
Yes
Picopower
No
Temp. Range (deg C)
-40 to 85
I/o Supply Class
1.8/3.3
Operating Voltage (vcc)
0.9 to 1.1
Fpu
No
Mpu / Mmu
No / Yes
Timers
6
Output Compare Channels
6
Input Capture Channels
6
Pwm Channels
4
32khz Rtc
Yes
Calibrated Rc Oscillator
No
Table 9-1.
9.3
9.3.1
9.3.2
9.4
40
Peripheral ID
Peripheral Interrupts and Clock Control
Peripheral Signals Multiplexing on I/O Lines
29
30
31
SAM9M11
System Interrupt
External Interrupts
SAM9M11 Peripheral Identifiers (Continued)
Peripheral Mnemonic
The System Interrupt in Source 1 is the wired-OR of the interrupt signals coming from:
The clock of these peripherals cannot be deactivated and Peripheral ID 1 can only be used
within the Advanced Interrupt Controller.
All external interrupt signals, i.e., the Fast Interrupt signal FIQ or the Interrupt signal IRQ, use a
dedicated Peripheral ID. However, there is no clock control associated with these peripheral IDs.
The SAM9M11 features 5 PIO controllers, PIOA, PIOB, PIOC, PIOD and PIOE, which multi-
plexes the I/O lines of the peripheral set.
Each PIO Controller controls up to 32 lines. Each line can be assigned to one of two peripheral
functions, A or B. The multiplexing tables in the following paragraphs define how the I/O lines of
the peripherals A and B are multiplexed on the PIO Controllers. The two columns “Function” and
“Comments” have been inserted in this table for the user’s own comments; they may be used to
track how pins are defined in an application.
Note that some peripheral function which are output only, might be duplicated within the both
tables.
The column “Reset State” indicates whether the PIO Line resets in I/O mode or in peripheral
mode. If I/O is mentioned, the PIO Line resets in input with the pull-up enabled, so that the
device is maintained in a static state as soon as the reset is released. As a result, the bit corre-
sponding to the PIO Line in the register PIO_PSR (Peripheral Status Register) resets low.
If a signal name is mentioned in the “Reset State” column, the PIO Line is assigned to this func-
tion and the corresponding bit in PIO_PSR resets high. This is the case of pins controlling
memories, in particular the address lines, which require the pin to be driven as soon as the reset
is released. Note that the pull-up resistor is also enabled in this case.
To amend EMC, programmable delay has been inserted on PIO lines able to run at high speed.
• the DDR2/LPDDR Controller
• the Debug Unit
• the Periodic Interval Timer
• the Real-Time Timer
• the Real-Time Clock
• the Watchdog Timer
• the Reset Controller
• the Power Management Controller
VDEC
MCI1
AIC
Peripheral Name
High Speed Multimedia Card Interface 1
Video Decoder
Advanced Interrupt Controller
6437CS–ATARM–8-Apr-11
External Interrupt
IRQ