LPC1776FBD208 NXP Semiconductors, LPC1776FBD208 Datasheet - Page 33

• Manufacturer Part Number: LPC1776FBD208
• Description: The LPC1776 is a Cortex-M3 microcontroller for embedded applications featuring a high level of integration and low power consumption at frequencies of 120 MHz
• Manufacturer: NXP Semiconductors

NXP Semiconductors
Table 3.
Not all functions are available on all parts. See
pins).
LPC178X_7X
Objective data sheet
Symbol
P4[31]
P5[0] to P5[4]
P5[0]
P5[1]
P5[2]
P5[3]
P5[4]
JTAG_TDO
(SWO)
JTAG_TDI
Pin description
193 A4
9
30
117 L14
141 G14 G10 98
206 C3
2
4
F4
J4
D3
C2
…continued
E7
H1
L12
E5
C4
B1
C3
134
6
21
81
143
1
3
[3]
[3]
[3]
[11]
[11]
[3]
[3]
[3]
All information provided in this document is subject to legal disclaimers.
I;
PU
I;
PU
I;
PU
<tb
d>
<tb
d>
I;
PU
Table 2
Rev. 3 — 27 December 2011
I/O
O
I/O
I/O
I/O
I/O
O
I/O
I/O
I/O
O
I/O
-
-
O
-
I/O
I/O
-
-
-
I
I/O
I/O
O
-
O
O
O
I
(Ethernet, USB, LCD, QEI, SD/MMC, DAC pins) and
Description
P4[31] — General purpose digital input/output pin.
EMC_CS1 — LOW active Chip Select 1 signal.
Port 5: Port 5 is a 5-bit I/O port with individual direction controls
for each bit. The operation of port 5 pins depends upon the pin
function selected via the pin connect block.
P5[0] — General purpose digital input/output pin.
EMC_A[24] — External memory address line 24.
SSP2_MOSI — Master Out Slave In for SSP2.
T2_MAT2 — Match output for Timer 2, channel 2.
P5[1] — General purpose digital input/output pin.
EMC_A[25] — External memory address line 25.
SSP2_MISO — Master In Slave Out for SSP2.
T2_MAT3 — Match output for Timer 2, channel 3.
P5[2] — General purpose digital input/output pin.
R — Function reserved.
R — Function reserved.
T3_MAT2 — Match output for Timer 3, channel 2.
R — Function reserved.
I2C0_SDA — I
I
P5[3] — General purpose digital input/output pin.
R — Function reserved.
R — Function reserved.
R — Function reserved.
U4_RXD — Receiver input for USART4.
I2C0_SCL — I
specialized I
P5[4] — General purpose digital input/output pin.
U0_OE — RS-485/EIA-485 output enable signal for UART0.
R — Function reserved.
T3_MAT3 — Match output for Timer 3, channel 3.
U4_TXD — Transmitter output for USART4 (input/output in
smart card mode).
Test Data Out for JTAG interface. Also used as Serial wire trace
output.
Test Data In for JTAG interface.
2
C pad that supports I
2
C pad that supports I
2
2
C0 clock input/output (this pin uses a
C0 data input/output (this pin uses a specialized
32-bit ARM Cortex-M3 microcontroller
2
C Fast Mode Plus).
2
C Fast Mode Plus.
LPC178x/7x
© NXP B.V. 2011. All rights reserved.
Table 7
33 of 120
(EMC