ST7263BH6 STMicroelectronics, ST7263BH6 Datasheet - Page 32
ST7263BH6
Manufacturer Part Number
ST7263BH6
Description
LOW SPEED USB 8-BIT MCU FAMILY WITH UP TO 32K FLASH/ROM, DFU CAPABILITY, 8-BIT ADC, WDG, TIMER, SCI and I2C
Manufacturer
STMicroelectronics
Datasheet
1.ST7263BH6.pdf
(186 pages)
Specifications of ST7263BH6
4, 8, 16 Or 32 Kbytes Program Memory
high density Flash (HDFlash), FastROM or ROM with Read-Out and Write protection
- Current page: 32 of 186
- Download datasheet (3Mb)
Reset and clock management
6
6.1
Caution:
6.1.1
6.1.2
6.1.3
32/186
Reset and clock management
Reset
The Reset procedure is used to provide an orderly software start-up or to exit low power
modes.
Three reset modes are provided: a low voltage (LVD) reset, a watchdog reset and an
external reset at the RESET pin.
A reset causes the reset vector to be fetched from addresses FFFEh and FFFFh in order to
be loaded into the PC and with program execution starting from this point.
An internal circuitry provides a 4096 CPU clock cycle delay from the time that the oscillator
becomes active.
When the ST7 is unprogrammed or fully erased, the Flash is blank and the RESET vector is
not programmed. For this reason, it is recommended to keep the RESET pin in low state
until programming mode is entered, in order to avoid unwanted behavior.
Low voltage detector (LVD)
Low voltage reset circuitry generates a reset when V
●
●
During low voltage reset, the RESET pin is held low, thus permitting the MCU to reset other
devices.
It is recommended to make sure that the V
device is exiting from Reset, to ensure the application functions properly.
Watchdog reset
When a watchdog reset occurs, the RESET pin is pulled low permitting the MCU to reset
other devices in the same way as the low voltage reset
External reset
The external reset is an active low input signal applied to the RESET pin of the MCU.
As shown in
CPU clock cycles.
An internal Schmitt trigger at the RESET pin is provided to improve noise immunity.
Below V
Below V
Figure
IT+
IT-
when V
when V
15, the RESET signal must stay low for a minimum of one and a half
DD
DD
is falling
is rising
Doc ID 7516 Rev 8
DD
supply voltage rises monotonously when the
DD
(Figure
is:
12).
ST7263Bxx
Related parts for ST7263BH6
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
LOW SPEED USB 8-BIT MCU FAMILY with up to 16K MEMORY, up to 512 BYTES RAM, 8-BIT ADC, WDG, TIMER, SCI & I2C
Manufacturer:
STMICROELECTRONICS [STMicroelectronics]
Datasheet:
Part Number:
Description:
MCU, MPU & DSP Development Tools ST7 Emulator Board
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet: