ST72324BK4-Auto STMicroelectronics, ST72324BK4-Auto Datasheet - Page 41
ST72324BK4-Auto
Manufacturer Part Number
ST72324BK4-Auto
Description
8-bit MCU for automotive, 3.8 to 5.5V operating range with 16 Kbyte Flash, 10-bit ADC, 4 timers, SPI, SCI
Manufacturer
STMicroelectronics
Datasheet
1.ST72324BJ2-AUTO.pdf
(198 pages)
Specifications of ST72324BK4-Auto
Hdflash Endurance
100 cycles, data retention 20 years
Clock Sources
crystal/ceramic resonator oscillators, internal RC oscillator and external clock input
4 Power Saving Modes
Slow, Wait, Active Halt, and Halt
- Current page: 41 of 198
- Download datasheet (3Mb)
ST72324B-Auto
7
7.1
7.2
Note:
Interrupts
Introduction
The ST7 enhanced interrupt management provides the following features:
●
●
●
This interrupt management is based on:
●
●
●
This enhanced interrupt controller guarantees full upward compatibility with the standard
(not nested) ST7 interrupt controller.
Masking and processing flow
The interrupt masking is managed by the I1 and I0 bits of the CC register and the ISPRx
registers which give the interrupt software priority level of each interrupt vector (see
Table
When an interrupt request has to be serviced:
●
●
●
●
The interrupt service routine should end with the IRET instruction which causes the
contents of the saved registers to be recovered from the stack.
As a consequence of the IRET instruction, the I1 and I0 bits will be restored from the stack
and the program in the previous level will resume.
Hardware interrupts
Software interrupt (TRAP)
Nested or concurrent interrupt management with flexible interrupt priority and level
management:
–
–
–
Bit 5 and bit 3 of the CPU CC register (I1:0)
Interrupt software priority registers (ISPRx)
Fixed interrupt vector addresses located at the high addresses of the memory map
(FFE0h to FFFFh) sorted by hardware priority order
Normal processing is suspended at the end of the current instruction execution.
The PC, X, A and CC registers are saved onto the stack.
I1 and I0 bits of CC register are set according to the corresponding values in the ISPRx
registers of the serviced interrupt vector.
The PC is then loaded with the interrupt vector of the interrupt to service and the first
instruction of the interrupt service routine is fetched (refer to
mapping
14). The processing flow is shown in
up to 4 software programmable nesting levels
up to 16 interrupt vectors fixed by hardware
2 non-maskable events: reset, TRAP
for vector addresses).
Doc ID13466 Rev 4
Figure 16.
Table 25: Interrupt
Interrupts
41/198
Related parts for ST72324BK4-Auto
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
3 V/5 V Range 8-bit Mcu With 4/8 Kbyte Rom, 10-bit Adc, Four Timers And Spi
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [RIPPLE-CARRY BINARY COUNTER/DIVIDERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
STMicroelectronics [LIQUID-CRYSTAL DISPLAY DRIVERS]
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
BOARD EVAL FOR MEMS SENSORS
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN TRANSISTOR POWER MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
TURBOSWITCH ULTRA-FAST HIGH VOLTAGE DIODE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
DIODE / SCR MODULE
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search -----> STE16N100
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
Search ---> STE53NA50
Manufacturer:
STMicroelectronics
Datasheet:
Part Number:
Description:
NPN Transistor Power Module
Manufacturer:
STMicroelectronics
Datasheet: