STR755FR2 STMicroelectronics, STR755FR2 Datasheet - Page 7
![no-image](/images/manufacturer_photos/0/6/637/stmicroelectronics_sml.jpg)
STR755FR2
Manufacturer Part Number
STR755FR2
Description
ARM7TDMI-S™ 32-BIT MCU with Flash, SMI, 3 std 16-bit timers, PWM timer, fast 10-bit ADC, I2C, UART, SSP, USB and CAN
Manufacturer
STMicroelectronics
Datasheet
1.STR755FV2.pdf
(84 pages)
Specifications of STR755FR2
Smart Low Power Modes
SLOW, WFI, STOP and STANDBY with backup registers
Conversion Time
min. 3.75 μs
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
STR755FR2H6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Company:
Part Number:
STR755FR2T6
Manufacturer:
STMicroelectronics
Quantity:
10 000
Part Number:
STR755FR2T6
Manufacturer:
ST
Quantity:
20 000
STR750Fxx STR751Fxx STR752Fxx STR755Fxx
Caution:
Caution:
●
When powered by 5.0V, the USB peripheral cannot operate.
Low power modes
The STR750F supports 5 low power modes, SLOW, PCG, WFI, STOP and STANDBY.
●
●
●
●
●
It is important to bear in mind that it is forbidden to remove power from the V
supply in any of the Low Power Modes (even in STANDBY MODE).
DMA
The flexible 4-channel general-purpose DMA is able to manage memory to memory,
peripheral to memory and memory to peripheral transfers. The DMA controller supports
circular buffer management avoiding the generation of interrupts when the controller
reaches the end of the buffer.
The DMA can be used with the main peripherals: UART0, SSP0, Motor control PWM timer
(PWM), standard timer TIM0 and ADC.
RTC (real-time clock)
The real-time clock provides a set of continuously running counters which can be used with
suitable software to provide a clock calendar function, and provides an alarm interrupt and a
regulator and the V
regulator. This scheme has the advantage of requiring only one 5.0V power source.
Power Scheme 4: Dual external 5.0V and 1.8V power sources. In this configuration,
the internal voltage regulators are switched off, by forcing the VREG_DIS pin to high
level. V
V
SLOW MODE: the system clock speed is reduced. Alternatively, the PLL and the main
oscillator can be stopped and the device is driven by a low power clock (f
clock is either an external 32.768 kHz oscillator or the internal low power RC oscillator.
PCG MODE (Peripheral Clock Gating MODE): When the peripherals are not used, their
APB clocks are gated to optimize the power consumption.
WFI MODE (Wait For Interrupts): only the CPU clock is stopped, all peripherals
continue to work and can wake-up the CPU when IRQs occur.
STOP MODE: all clocks/peripherals are disabled. It is also possible to disable the
oscillators and the Main Voltage Regulator (In this case the V
by V
SRAM and registers contents retained. The system can be woken up by any of the
external interrupts / wake-up lines or by the RTC timer which can optionally be kept
running. The RTC can be clocked either by the 32.768 kHz Crystal or the Low Power
RC Oscillator.
Alternatively, STOP mode gives flexibility to keep the either main oscillator, or the Flash
or the Main Voltage Regulator enabled when a fast start after wake-up is preferred (at
the cost of some extra power consumption).
STANDBY MODE: This mode (only available in single supply power schemes) is
intended to achieve the lowest power consumption even when the temperature is
increasing. The digital power supply (V
at high ambient temperature). SRAM and all register contents are lost. Only the RTC
remains powered by V
RUN mode by a trigger event on the WKP_STDBY pin or an alarm timeout on the RTC
counter.
BACKUP
18_BKP
CORE
through the V
). This mode is intended to achieve the lowest power consumption with
is provided externally through the V
BACKUP
18_BKP
18_BKP
supply is generated internally by the low power voltage
. The STR750F can be switched back from STANDBY to
pin. This scheme is intended to provide 5V I/O capability.
CORE
) is completely removed (no leakage even
18
and V
18REG
CORE
power pins and
is entirely powered
DD_IO
RTC
Introduction
). The
power
7/84