TDA9881TS/V2,518 NXP Semiconductors, TDA9881TS/V2,518 Datasheet
![IC IF-PLL DEMOD 24-SSOP](/photos/6/52/65222/568-24-ssop_sot340-1_sml.jpg)
TDA9881TS/V2,518
Specifications of TDA9881TS/V2,518
TDA9881TS/V2-T
TDA9881TS/V2-T
Related parts for TDA9881TS/V2,518
TDA9881TS/V2,518 Summary of contents
Page 1
TDA9881 Alignment-free vision and FM sound IF PLL demodulator for negative modulated TV standards Rev. 01 — 16 November 2004 1. General description The TDA9881 is an alignment-free multistandard (PAL and NTSC) vision and sound IF signal PLL demodulator for ...
Page 2
Philips Semiconductors 4. Quick reference data Table 1: Quick reference data Symbol Parameter V supply voltage P I supply current P Video part V VIF input voltage sensitivity i(VIF)(rms) (RMS value) G VIF gain control range VIF(cr) f vision carrier ...
Page 3
Philips Semiconductors Table 1: Quick reference data Symbol Parameter PSRR power supply ripple rejection FMSO on pin FMSO V IF intercarrier output level o(intc)(rms) (RMS value) Reference frequency f reference signal frequency ref V reference signal voltage ref(rms) (RMS value) ...
Page 4
TOP TAGC VAGC 9 (8) 14 (15) 22 (24) C AGC TUNER AGC VIF AGC VIF2 2 (31) VIF PLL VIF1 1 (30) SIF2 24 (27) SINGLE REFERENCE QSS MIXER INTERCARRIER MIXER SIF1 23 (26) SUPPLY SIF AGC C AGC ...
Page 5
Philips Semiconductors 7. Pinning information 7.1 Pinning VIF1 1 VIF2 2 3 i.c. FMPLL 4 DEEM 5 6 AFD TDA9881TS 7 DGND FMSO 8 TOP 9 10 FM1 FM0 11 QSSO 12 Fig 2. Pin configuration for SSOP24. 9397 750 ...
Page 6
Philips Semiconductors 7.2 Pin description Table 3: Symbol VIF1 VIF2 n.c. i.c. FMPLL DEEM AFD DGND n.c. FMSO TOP FM1 FM0 QSSO n.c. n.c. VIF0 TAGC REF AMUTE0 16 CVBS n.c. AGND VPLL V P AFC VAGC n.c. SIF1 SIF2 ...
Page 7
Philips Semiconductors 8. Functional description A simplified block diagram of the device is illustrated in following functional blocks: 1. VIF amplifier 2. Tuner AGC and VIF AGC 3. VIF AGC detector 4. Frequency Phase-Locked Loop (FPLL) detector 5. VCO and ...
Page 8
Philips Semiconductors 8.4 FPLL detector The VIF amplifier output signal is fed to a frequency detector and a phase detector via a limiting amplifier to remove the video AM. During acquisition the frequency detector produces a current that is proportional ...
Page 9
Philips Semiconductors The AFC signal is derived from the corresponding downcounter stop value after a counting cycle. The last four bits are latched and the digital-to-analog converted value is given as current at pin AFC. 8.7 Video demodulator and amplifier ...
Page 10
Philips Semiconductors 8.11 Single reference QSS mixer With the present system high performance Hi-Fi stereo sound processing can be achieved. For a simplified application without an SIF SAW filter, the single reference QSS mixer can be switched to the intercarrier ...
Page 11
Philips Semiconductors 8.13 Audio amplifier and mute time constant The audio amplifier consists of two parts: • AF preamplifier • AF output amplifier. The AF preamplifier used for FM sound is an operational amplifier with internal feedback, high gain and ...
Page 12
Philips Semiconductors Table 5: FM0 Pin open-circuit Pin connected to ground Pin open-circuit Pin connected to ground Table 6: AMUTE0 Pin open-circuit Pin connected to ground Table 7: SIF1 and SIF2 No DC path to ground One or both pins ...
Page 13
Philips Semiconductors 10. Thermal characteristics Table 9: Thermal characteristics Symbol Parameter R thermal resistance from junction to ambient th(j-a) TDA9881TS (SSOP24) TDA9881HN (HVQFN32) 11. Characteristics Table 10: Characteristics see Table 12 P ...
Page 14
Philips Semiconductors Table 10: Characteristics …continued see Table 12 P amb f = 33.4 MHz; PC/ dB broadband transformer video modulation DSB; residual carrier for ...
Page 15
Philips Semiconductors Table 10: Characteristics …continued see Table 12 P amb f = 33.4 MHz; PC/ dB broadband transformer video modulation DSB; residual carrier for ...
Page 16
Philips Semiconductors Table 10: Characteristics …continued see Table 12 P amb f = 33.4 MHz; PC/ dB broadband transformer video modulation DSB; residual carrier for ...
Page 17
Philips Semiconductors Table 10: Characteristics …continued see Table 12 P amb f = 33.4 MHz; PC/ dB broadband transformer video modulation DSB; residual carrier for ...
Page 18
Philips Semiconductors Table 10: Characteristics …continued see Table 12 P amb f = 33.4 MHz; PC/ dB broadband transformer video modulation DSB; residual carrier for ...
Page 19
Philips Semiconductors Table 10: Characteristics …continued see Table 12 P amb f = 33.4 MHz; PC/ dB broadband transformer video modulation DSB; residual carrier for ...
Page 20
Philips Semiconductors Table 10: Characteristics …continued see Table 12 P amb f = 33.4 MHz; PC/ dB broadband transformer video modulation DSB; residual carrier for ...
Page 21
Philips Semiconductors Table 10: Characteristics …continued see Table 12 P amb f = 33.4 MHz; PC/ dB broadband transformer video modulation DSB; residual carrier for ...
Page 22
Philips Semiconductors Table 10: Characteristics …continued see Table 12 P amb f = 33.4 MHz; PC/ dB broadband transformer video modulation DSB; residual carrier for ...
Page 23
Philips Semiconductors [2] Level headroom for input level jumps during gain control setting. [3] This parameter is not tested during the production and is only given as application information for designing the receiver circuit. [4] Loop bandwidth ...
Page 24
Philips Semiconductors [21] For all S/N measurements the used VIF modulator has to meet the following specifications: a) Incidental phase modulation for black-to-white jump less than 0.5 degrees. b) QSS AF performance, measured with the television demodulator AMF2 (audio output, ...
Page 25
Philips Semiconductors Fig 4. Typical video signal levels on output pin CVBS (sound carrier off). Fig 5. Ripple rejection condition. 9397 750 13417 Product data sheet Alignment-free vision and FM sound IF PLL demodulator video 2 V (p-p) 3.41 V ...
Page 26
Philips Semiconductors ( VIF AGC voltage and can be measured at pin VAGC. VAGC ( tuner current in TV mode with R TAGC ( tuner current in TV mode with R TAGC (4) I ...
Page 27
Philips Semiconductors AFC 21 TDA9881 (23) Pin numbers for TDA9881HN in parenthesis. Fig 9. Typical analog AFC characteristic. 80 S/N (dB Fig 10. Typical signal-to-noise ratio as a function of ...
Page 28
Philips Semiconductors 10 H(s) (dB Fig 12. Typical amplitude response for sound trap at M/N standard (inclusive Korea). 400 group delay (ns) 300 200 100 0 100 0 0.5 Overall delay is not shown, ...
Page 29
Philips Semiconductors 10 H(s) (dB Fig 14. Typical amplitude response for sound trap at B/G standard. 400 group delay (ns) 300 200 100 0 100 0 0.5 1 Overall delay is not shown, here ...
Page 30
Philips Semiconductors Fig 16. Typical amplitude response for sound trap at I standard. Fig 17. Typical amplitude response for sound trap at D/K standard. 9397 750 13417 Product data sheet Alignment-free vision and FM sound IF PLL demodulator 10 H(s) ...
Page 31
Philips Semiconductors 10 0 S/N W (dB Conditions: PC/SC ratio is measured at pins VIF1 and VIF2; via transformer; 27 kHz FM deviation de-emphasis. (1) Signal. (2) ...
Page 32
Philips Semiconductors antenna input (dB V) (1) Depends on TOP. Fig 19. Front-end level diagram. 9397 750 13417 Product data sheet Alignment-free vision and FM sound IF PLL demodulator 140 120 (1) 100 80 tuning gain control range 60 40 ...
Page 33
SAW FILTER 2 4 K9350 3 SIF2 SIF1 24 23 (27) (26) (24) (30) (31 VIF1 VIF2 IF input 1 5 SAW FILTER G3962 3 Pin numbers for TDA9881HN in parenthesis. (1) Optional ...
Page 34
SIF input SIF2 SIF1 VAGC (27) (26) (24) (31) (1) (30 (2) VIF1 VIF2 i.c. VIF input 51 Pin numbers for TDA9881HN in parenthesis. (1) ...
Page 35
Philips Semiconductors 14. Package outline SSOP24: plastic shrink small outline package; 24 leads; body width 5 pin 1 index 1 DIMENSIONS (mm are the original dimensions) A UNIT max. 0.21 ...
Page 36
Philips Semiconductors HVQFN32: plastic thermal enhanced very thin quad flat package; no leads; 32 terminals; body 0.85 mm terminal 1 index area terminal 1 32 index area DIMENSIONS (mm ...
Page 37
Philips Semiconductors 15. Soldering 15.1 Introduction to soldering surface mount packages This text gives a very brief insight to a complex technology. A more in-depth account of soldering ICs can be found in our Data Handbook IC26; Integrated Circuit Packages ...
Page 38
Philips Semiconductors – smaller than 1.27 mm, the footprint longitudinal axis must be parallel to the transport direction of the printed-circuit board. The footprint must incorporate solder thieves at the downstream end. • For packages with leads on four sides, ...
Page 39
Philips Semiconductors [4] These packages are not suitable for wave soldering. On versions with the heatsink on the bottom side, the solder cannot penetrate between the printed-circuit board and the heatsink. On versions with the heatsink on the top side, ...
Page 40
Philips Semiconductors 16. Revision history Table 14: Revision history Document ID Release date TDA9881_1 20041116 9397 750 13417 Product data sheet Alignment-free vision and FM sound IF PLL demodulator Data sheet status Change notice Product data sheet - Rev. 01 ...
Page 41
Philips Semiconductors 17. Data sheet status [1] Level Data sheet status Product status I Objective data Development II Preliminary data Qualification III Product data Production [1] Please consult the most recently issued data sheet before initiating or completing a design. ...
Page 42
Philips Semiconductors 21. Contents 1 General description . . . . . . . . . . . . . . . . . . . . . . 1 2 Features . . . . . . . . ...