PIC16C926 Microchip Technology Inc., PIC16C926 Datasheet - Page 143

• Manufacturer Part Number: PIC16C926
• Description: 64/68-pin Cmos Microcontrollers With Lcd Driver
• Manufacturer: Microchip Technology Inc.

15.1
PIC16LC925/926
PIC16C925/926
D001
D001A
D001
D001A
D002
D003
D004
D005
D010
D011
D010
D011
D012
Note 1: This is the limit to which V
Param
2001 Microchip Technology Inc.
No.
(Commercial, Industrial)
(Commercial, Industrial)
† Data in "Typ" column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance only
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin load-
3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is
4: For RC osc configuration, current through R
5: The
6: PWRT must be enabled for slow ramps.
7:
DC Characteristics
V
V
V
S
V
I
DD
and are not tested.
ing and switching rate, oscillator type, internal code execution pattern, and temperature also have an impact on
the current consumption.The test conditions for all I
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to V
mated by the formula Ir = V
added to the base I
circuitry. This does not include current dissipated by the LCD panel.
DD
DR
POR
VDD
BOR
Sym
LCDT
current is the additional current consumed when this peripheral is enabled. This current should be
1 and
Supply Voltage
RAM Data Retention
Voltage (Note 1)
V
to ensure internal
Power-on Reset signal
V
to ensure internal
Power-on Reset signal
Brown-out Reset
voltage trip point
Supply Current (Note 2)
OSC1 = external square wave, from rail to rail;
all I/O pins tri-stated, pulled to V
MCLR = V
DD
DD
Characteristic
Start Voltage
Rise Rate
LCDRC
PIC16LC925/926
PIC16LC925/926
PIC16C925/926
PIC16C925/926
DD
DD
includes the current consumed by the LCD Module and the voltage generation
or I
.
DD
PD
DD
measurement.
can be lowered in SLEEP mode without losing RAM data.
/2R
EXT
Standard Operating Conditions (unless otherwise stated)
Operating temperature
Standard Operating Conditions (unless otherwise stated)
Operating temperature
0.05
3.65
Min
2.5
4.5
4.0
4.5
—
—
—
—
—
—
—
(mA) with R
Preliminary
Typ† Max Units
DD
V
225
1.5
2.7
35
EXT
—
—
—
—
—
—
.6
7
SS
is not included. The current through the resistor can be esti-
DD
4.35
EXT
5.5
5.5
5.5
5.5
2.0
—
—
—
48
70
10
5
measurements in active operation mode are:
in kOhm.
V/ms See Power-on Reset section for details
mA
mA
mA
V
V
V
V
V
V
V
A
A
-40°C
-40°C
LP, XT and RC osc configuration
HS osc configuration
XT, RC and LP osc configuration
HS osc configuration
Device in SLEEP mode
See Power-on Reset section for details
(Note 6)
BODEN bit set
XT and RC osc configuration
F
LP osc configuration
F
XT and RC osc configuration
F
LP osc configuration
F
HS osc configuration
F
OSC
OSC
OSC
OSC
OSC
0°C
0°C
PIC16C925/926
= 4 MHz, V
= 32 kHz, V
= 4 MHz, V
= 32 kHz, V
= 20 MHz, V
T
T
T
T
A
A
A
A
+85°C for industrial
+70°C for commercial
+85°C for industrial
+70°C for commercial
Conditions
DD
DD
DD
DD
DD
= 3.0V (Note 4)
= 5.5V (Note 4)
= 3.0V, WDT disabled
= 4.0V
= 5.5V
DS39544A-page 141
DD
and V
SS
.