MT8920BC Zarlink Semiconductor, MT8920BC Datasheet - Page 3
![no-image](/images/manufacturer_photos/0/7/727/zarlink_semiconductor_sml.jpg)
MT8920BC
Manufacturer Part Number
MT8920BC
Description
MT8920 - 32 Channels TDM (ST-BUS) to Parallel Bus Access Circuit
Manufacturer
Zarlink Semiconductor
Datasheet
1.MT8920BC.pdf
(27 pages)
Data Sheet
‡ Pin Descriptions pertain to all modes unless otherwise stated.
Pin Description (continued)
Mode
15-22
Pin #
1
2
3
13
14
23
24
25
26
27
28
MMS
1
0
0
DTACK Data Transfer Acknowledge (Mode 1). This open drain output is supplied by the STPA to
D0-D7 Bidirectional Data Bus. This bus is used to transfer data to or from the STPA during a write
Name
STCH Start of Channel (Mode 3). This signal is a low going pulse which indicates the start of an
BUSY BUSY (Mode 2). This open drain output signals that the controller and the ST-BUS are
24/32 24 Channel/32 Channel Select (Mode 2,3).
MMS
STo0
STo1
DCS
V
IRQ
V
A5
A5
DD
SS
MS1
N/A
1
0
Address Bit A5 (Mode 1). This input is used to extend the address range of the STPA. A5
selects internal registers when high and Tx/Rx RAM’s when low.
Address Bit A5 (Mode 2). This input is used to extend the address range of the STPA. A5
selects Tx0/Rx0 RAM’s when low and Tx1/Rx0 RAM’s when high.
ST-BUS channel. The pulse is four bits wide and begins at the start of each valid channel.
Ground.
or read operation.
ST-BUS Output 0. This output supplies the output ST-BUS 2048 kbit/s serial data stream from
Tx0 two-port RAM.
ST-BUS Output 1. In modes 1 and 2 this output supplies the output ST-BUS 2048 kbit/s serial
data stream from Tx1 two-port RAM. In mode 3, information arriving at STi0 is output here with
one frame delay.
Interrupt Request (Mode 1). This open drain output, when low, indicates when an interrupt
condition has been raised within the STPA.
configuration in modes 2 and 3. A low applied to this pin will select a 24 (T1) channel mode
while a high will select a 32 (CEPT) channel mode.
acknowledge the completion of data transfers back to the µP. On a read of the STPA, DTACK
low indicates that the STPA has put valid data on the data bus. On a write, DTACK low
indicates that the STPA has completed latching the µP’s data from the data bus.
accessing the same location in the dual-port RAM’s. It is intended to delay the controller
access until after the ST-BUS completes its access.
Delayed Chip Select (Mode 3). This low going pulse, which is four bit cells long, is active
during the last half of a valid channel. This signal is used to daisy-chain together two STPA’s in
mode 3 that are accessing devices on the same parallel data bus.
Master Mode Select (Reset). This Schmitt trigger input selects between either mode 1 (MMS
= 1), or modes 2and 3 (MMS = 0). If MMS is pulsed low in Mode 1 operation the control and
interrupt registers will be reset. (Refer to Table 1.) During power-up, the time constant of the
reset circuit (see Fig. 8) must be a minimum of five times the rise time of the power supply.
Power Supply Input. (+5V).
Peripheral
Fast RAM
Controller
Operation
Mode of
Mode
Mode
Mode
Bus
µ
P
The STPA provides parallel-to-serial and serial-to-parallel conversions through a
68000-type interface. Two Tx RAMs and one Rx RAM are available along with full
interrupt capability. 32 channel or 24 channel support is available. Control Register 1, bit
D
operation.
The STPA provides a fast access interface to Tx0, Tx1 and Rx0 RAMs. This mode is
intended for full parallel support of 24 channel T1/ESF trunks and 32 channel CEPT
trunks. Input 24/32 (pin 25) = 0 for 24 channel operation, input 24/32 (pin 25) = 1 for 32
channel operation.
The STPA will synchronously drive the parallel bus using the address generator and
provide all data transfer signals. This mode is intended to support 24 or 32 channel
devices in the absence of a parallel bus controller. Input 24/32 (pin 25) = 0 for 24 channel
operation, input 24/32 (pin 25) = 1 for 32 channel operation.
5
(RAMCON) = 0 for 32 channel operation and D
Table 1. STPA Modes of Operation
Description
This input is used to select the channel
Function
‡
5
(RAMCON)= 1 for 24 channel
MT8920B
3