MT16LSDT6464A Micron Technology, MT16LSDT6464A Datasheet - Page 8
![no-image](/images/no-image-200.jpg)
MT16LSDT6464A
Manufacturer Part Number
MT16LSDT6464A
Description
SYNCHRONOUS DRAM MODULE
Manufacturer
Micron Technology
Datasheet
1.MT16LSDT6464A.pdf
(24 pages)
www.DataSheet4U.com
MAND INHIBIT or NOP . Starting at some point during
this 100µs period and continuing at least through the
end of this period, COMMAND INHIBIT or NOP com-
mands should be applied.
one COMMAND INHIBIT or NOP command having
been applied, a PRECHARGE command should be
applied. All device banks must then be precharged,
thereby placing the device in the all banks idle state.
must be performed. After the AUTO REFRESH cycles
are complete, the SDRAM is ready for mode register
programming. Because the mode register will power
up in an unknown state, it should be loaded prior to
applying any operational command.
Mode Register Definition
mode of operation of the SDRAM. This definition
includes the selection of a burst length, a burst type, a
CAS latency, an operating mode and a write burst
mode, as shown in Figure 5, Mode Register Definition
Diagram, on page 8. The mode register is programmed
via the LOAD MODE REGISTER command and will
retain the stored information until it is programmed
again or the device loses power.
M3 specifies the type of burst (sequential or inter-
leaved), M4–M6 specify the CAS latency, M7 and M8
specify the operating mode, M9 specifies the write
burst mode, and M10 and M11 are reserved for future
use.
banks are idle, and the controller must wait the speci-
fied time before initiating the subsequent operation.
Violating either of these requirements will result in
unspecified operation.
Burst Length
ented, with the burst length being programmable, as
shown in Figure 5, Mode Register Definition Diagram,
on page 8. The burst length determines the maximum
number of column locations that can be accessed for a
given READ or WRITE command. Burst lengths of 1, 2,
4, or 8 locations are available for both the sequential
and the interleaved burst types, and a full-page burst is
available for the sequential type. The full-page burst is
used in conjunction with the BURST TERMINATE
command to generate arbitrary burst lengths.
32,64 Meg x 64 SDRAM DIMMs
SD8_16C32_64x64AG_C.fm - Rev. C 11/02
Once the 100µs delay has been satisfied with at least
Once in the idle state, two AUTO REFRESH cycles
The mode register is used to define the specific
Mode register bits M0–M2 specify the burst length,
The mode register must be loaded when all device
Read and write accesses to the SDRAM are burst ori-
Figure 5: Mode Register Definition
8
operation or incompatibility with future versions may
result.
of columns equal to the burst length is effectively
selected. All accesses for that burst take place within
this block, meaning that the burst will wrap within the
block if a boundary is reached, as shown in the Burst
Definition Table. The block is uniquely selected by A1–
A9 when the burst length is set to two; A2–A9 when the
burst length is set to four; and by A3–A9 when the burst
length is set to eight. The remaining (least significant)
address bit(s) is (are) used to select the starting loca-
tion within the block. Full-page bursts wrap within the
page if the boundary is reached, as shown in Table 7,
Burst Definitions, on page 9.
Burst Type
to be either sequential or interleaved; this is referred to
as the burst type and is selected via bit M3.
mined by the burst length, the burst type, and the
starting column adress, as shown in Table 7, Burst Def-
initions, on page 9.
Reserved states should not be used, as unknown
When a READ or WRITE command is issued, a block
Accesses within a given burst may be programmed
The ordering of the accesses within a burst is deter-
Micron Technology, Inc., reserves the right to change products or specifications without notice.
168-PIN SDRAM DIMMs
256MB / 512MB (x64)
©2002, Micron Technology Inc.