MT16VDDF6464HY-335 Micron, MT16VDDF6464HY-335 Datasheet - Page 22
![no-image](/images/no-image-200.jpg)
MT16VDDF6464HY-335
Manufacturer Part Number
MT16VDDF6464HY-335
Description
SMALL-OUTLINE DDR SDRAM DIMM
Manufacturer
Micron
Datasheet
1.MT16VDDF6464HY-335.pdf
(31 pages)
09005aef80a646bc
DDF16C64_128x64HG_B.fm - Rev. B 7/03 EN
30.
31. READs and WRITEs with auto precharge are not
32. Any positive glitch must be less than 1/3 of the
33. Normal Output Drive Curves:
Figure 9: Pull-Down Characteristics
t
minimum actually applied to the device CK and
CK# inputs, collectively during bank active.
allowed to be issued until
fied prior to the internal precharge command
being issued.
clock and not more than +400mV or 2.9V, which-
ever is less. Any negative glitch must be less than
1/3 of the clock cycle and not exceed either -
300mV or 2.2V, whichever is more positive.
HP min is the lesser of
a. The full variation in driver pull-down current
b. The variation in driver pull-down current
c. The full variation in driver pull-up current
d. The variation in driver pull-up current within
e. The full variation in the ratio of the maximum
from minimum to maximum process, temper-
ature and voltage will lie within the outer
bounding lines of the V-I curve of Figure 9,
Pull-Down Characteristics.
within nominal limits of voltage and tempera-
ture is expected, but not guaranteed, to lie
within the inner bounding lines of the V-I
curve of Figure 9, Pull-Down Characteristics.
from minimum to maximum process, temper-
ature and voltage will lie within the outer
bounding lines of the V-I curve of Figure 10,
Pull-Up Characteristics.
nominal limits of voltage and temperature is
expected, but not guaranteed, to lie within the
inner bounding lines of the V-I curve of Figure
10, Pull-Up Characteristics.
to minimum pull-up and pull-down current
should be between 0.71 and 1.4, for device
t
t
CL minimum and
RAS(MIN) can be satis-
t
CH
22
34. The voltage levels used are derived from a mini-
35. V
36. V
37. This maximum value is derived from the refer-
38. For slew rates greater than 1V/ns the (LZ) transi-
39. During Initialization, V
40. The current Micron part operates below the slow-
Figure 10: Pull-Up Characteristics
mum V
practice, the voltage levels obtained from a prop-
erly terminated bus will provide significantly dif-
ferent voltage values.
pulse width £ 3ns and the pulse width can not be
greater than 1/3 of the cycle rate. V
V
pulse width can not be greater than 1/3 of the
cycle rate.
enced test load. In practice, the values obtained
in a typical terminated design may reflect up to
310ps less for
(MAX) will prevail over
(MAX) condition.
t
tion will start about 310ps earlier.
be equal to or less than V
V
even if V
of 42 W of series resistance is used between the V
supply and the input pin.
est JEDEC operating frequency of 83 MHz. As
such, future die may not reflect this option.
f. The full variation in the ratio of the nominal
DQSCK (MIN) +
Micron Technology, Inc., reserves the right to change products or specifications without notice.
IH
IL
DD
TT
drain-to-source voltages from 0.1V to 1.0V, and
at the same voltage and temperature.
pull-up to pull-down current should be unity
±10 percent, for device drain-to-source volt-
ages from 0.1V to 1.0V.
(MIN) = -1.5V for a pulse width £ 3ns and the
and V
may be 1.35V maximum during power up,
overshoot: V
DD
DD
DD
level and the referenced test load. In
/V
200-PIN DDR SODIMM
Q must track each other.
DD
t
HZ(MAX) and the last DVW.
Q are 0.0V, provided a minimum
t
RPRE (MAX) condition.
IH
512MB, 1GB (x64)
t
LZ (MIN) will prevail over
(MAX) = V
DD
t
DQSCK (MAX) +
DD
Q, V
+ 0.3V. Alternatively,
TT
DD
, and V
©2003 Micron Technology, Inc.
Q + 1.5V for a
IL
undershoot:
REF
t
RPST
must
t
HZ
TT