MX29LV320MB Macronix International, MX29LV320MB Datasheet - Page 22

• Manufacturer Part Number: MX29LV320MB
• Description: 32M-BIT [4M x 8/2M x 16] SINGLE VOLTAGE 3V ONLY FLASH MEMORY
• Manufacturer: Macronix International

SECTOR ERASE COMMANDS
The Automatic Sector Erase does not require the device
to be entirely pre-programmed prior to executing the Au-
tomatic Set-up Sector Erase command and Automatic
Sector Erase command. Upon executing the Automatic
Sector Erase command, the device will automatically pro-
gram and verify the sector(s) memory for an all-zero data
pattern. The system is not required to provide any con-
trol or timing during these operations.
When the sector(s) is automatically verified to contain an
all-zero pattern, a self-timed sector erase and verify be-
gin. The erase and verify operations are complete when
the data on Q7 is "1" and the data on Q6 stops toggling
for two consecutive read cycles, at which time the de-
vice returns to the Read mode. The system is not re-
quired to provide any control or timing during these opera-
tions.
When using the Automatic Sector Erase algorithm, note
that the erase automatically terminates when adequate
erase margin has been achieved for the memory array
(no erase verification command is required). Sector erase
is a six-bus cycle operation. There are two "unlock" write
cycles. These are followed by writing the set-up com-
mand 80H. Two more "unlock" write cycles are then fol-
lowed by the sector erase command 30H. The sector
address is latched on the falling edge of WE# or CE#,
whichever happens later , while the command (data) is
latched on the rising edge of WE# or CE#, whichever
happens first. Sector addresses selected are loaded
into internal register on the sixth falling edge of WE# or
CE#, whichever happens later. Each successive sector
load cycle started by the falling edge of WE# or CE#,
whichever happens later must begin within 50us from
the rising edge of the preceding WE# or CE#, whichever
happens first. Otherwise, the loading period ends and
internal auto sector erase cycle starts. (Monitor Q3 to
determine if the sector erase timer window is still open,
see section Q3, Sector Erase Timer.) Any command other
than Sector Erase(30H) or Erase Suspend(B0H) during
the time-out period resets the device to read mode.
ERASE SUSPEND
This command only has meaning while the state ma-
chine is executing Automatic Sector Erase operation, and
therefore will only be responded during Automatic Sector
Erase operation. When the Erase Suspend command is
issued during the sector erase operation, the device re-
P/N:PM1129
22
quires a maximum 20us to suspend the sector erase
operation. However, When the Erase Suspend command
is written during the sector erase time-out, the device
immediately terminates the time-out period and suspends
the erase operation. After this command has been ex-
ecuted, the command register will initiate erase suspend
mode. The state machine will return to read mode auto-
matically after suspend is ready. At this time, state ma-
chine only allows the command register to respond to the
Erase Resume, program data to, or read data from any
sector not selected for erasure.
The system can determine the status of the program
operation using the Q7 or Q6 status bits, just as in the
standard program operation. After an erase-suspend pro-
gram operation is complete, the system can once again
read array data within non-suspended blocks.
ERASE RESUME
This command will cause the command register to clear
the suspend state and return back to Sector Erase mode
but only if an Erase Suspend command was previously
issued. Erase Resume will not have any effect in all
other conditions. Another Erase Suspend command can
be written after the chip has resumed erasing.
MX29LV320MT/B
REV. 1.1 , JUL. 14, 2005
www.DataSheet4U.com