ds26518 Maxim Integrated Products, Inc., ds26518 Datasheet - Page 157
![no-image](/images/no-image-200.jpg)
ds26518
Manufacturer Part Number
ds26518
Description
8-port T1/e1/j1 Transceiver
Manufacturer
Maxim Integrated Products, Inc.
Datasheet
1.DS26518.pdf
(286 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
DS26518
Manufacturer:
DALLAS
Quantity:
20 000
Part Number:
ds26518-N
Manufacturer:
DALLAS
Quantity:
20 000
Company:
Part Number:
ds26518GN+
Manufacturer:
Maxim Integrated Products
Quantity:
135
Company:
Part Number:
ds26518GN+
Manufacturer:
TI
Quantity:
518
Part Number:
ds26518GN+
Manufacturer:
MAXIM/美信
Quantity:
20 000
Company:
Part Number:
ds26518GNB1
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
ds26518GNB1+
Manufacturer:
Maxim Integrated
Quantity:
10 000
Company:
Part Number:
ds26518NB1+
Manufacturer:
Maxim Integrated
Quantity:
10 000
Register Name:
Register Description:
Register Address:
Bit #
Name
Default
Bit 6: u-Law or A-Law Digital Milliwatt Code Select (uALAW)
Bit 5: RSERn Control (RSERC)
Bits 4 and 3: Receive Bit Inversion (BINV[1:0])
Bit 1: Payload Loopback (PLB)
When PLB is enabled, the following will occur:
In a PLB situation, the DS26518 will loop the 192 bits (248 for E1) of payload data (with BPVs corrected) from the
receive section back to the transmit section. The transmitter will follow the frame alignment provided by the
receiver. The receive frame boundary is automatically fed into the transmit section, such that the transmit frame
position is locked to the receiver (i.e., TSYNCn is sourced from RSYNCn). The FPS framing pattern, CRC-6
calculation, and the FDL bits (FAS word, Si, Sa, E bits, and CRC-4 for E1) are not looped back, they are reinserted
by the DS26518 (i.e., the transmit section will modify the payload as if it was input at TSERn).
Bit 0: Framer Loopback (FLB)
This loopback is useful in testing and debugging applications. In FLB, the DS26518 will loop data from the transmit
side back to the receive side. When FLB is enabled, the following will occur:
1) Data will be transmitted on TTIPn and TRINGn synchronous with RCLKn instead of TCLKn.
2) All of the receive-side signals will continue to operate normally.
3) The TCHCLKn and TCHBLKn signals are forced low.
4) Data at the TSERn, TDATAn, and TSIGn pins is ignored.
0 = u-law code is inserted based on T1RDMWE1–3 or E1RDMWE1–4 registers.
1 = A-law code is inserted based on T1RDMWE1–3 or E1RDMWE1–4 registers.
0 = Allow RSERn to output data as received under all conditions (normal operation).
1 = Force RSERn to one under loss of frame alignment conditions.
00 = No inversion.
01 = Invert framing.
10 = Invert signaling.
11 = Invert payload.
0 = Loopback disabled.
1 = Loopback enabled.
0 = loopback disabled
1 = loopback enabled
1) (T1 mode) an unframed all-ones code will be transmitted at TTIPn and TRINGn.
2) Data at RTIPn and RRINGn will be ignored.
3) All receive-side signals will take on timing synchronous with TCLKn instead of RCLKn.
Note that it is not acceptable to have RCLKn tied to TCLKn during this loopback because this will cause an
unstable condition.
(E1 mode) normal data will be transmitted at TTIPn and TRINGn.
—
7
0
RCR3
Receive Control Register 3
083h + (200h x (n - 1)) : where n = 1 to 8
uALAW
6
0
RSERC
5
0
157 of 286
BINV1
4
0
BINV0
3
0
DS26518 8-Port T1/E1/J1 Transceiver
—
2
0
PLB
1
0
FLB
0
0