isl6237 Intersil Corporation, isl6237 Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/3/342/intersil_corporation_sml.jpg)
isl6237
Manufacturer Part Number
isl6237
Description
High-efficiency, Quad-output, Main Power Supply Controllers For Notebook Computers
Manufacturer
Intersil Corporation
Datasheet
1.ISL6237.pdf
(34 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
isl6237IRZ
Manufacturer:
INTERSIL
Quantity:
14
Part Number:
isl6237IRZ
Manufacturer:
INTERSIL
Quantity:
20 000
Part Number:
isl6237IRZ-T
Manufacturer:
INTERSIL
Quantity:
20 000
Pin Descriptions
Typical Performance Curves
100
FIGURE 1. V
90
80
70
60
50
40
30
20
10
PIN
0
24
25
26
27
28
29
30
31
32
0.001
7 V
7 V
7 V
12 V
12 V
IN
IN
IN
IN
IN
SKIP MODE
PWM MODE
ULTRA SKIP MODE
PHASE2
UGATE2
REFIN2
OUT2
BOOT2
SKIP MODE
PWM MODE
NAME
SKIP#
POK2
OUT2
ILIM2
EN2
0.010
= 1.05V EFFICIENCY vs LOAD (300kHz)
(Continued)
OUTPUT LOAD (A)
Boost Flying Capacitor Connection for SMPS2. Connect to an external capacitor according to the typical application
circuits (Figure 62 and Figure 63). See “MOSFET Gate Drivers (UGATE_, LGATE_)” on page 27.
Inductor Connection for SMPS2. PHASE2 is the internal lower supply rail for the UGATE2 high-side gate driver.
PHASE2 is the current-sense input for the SMPS2.
High-Side MOSFET Floating Gate-Driver Output for SMPS2. UGATE1 swings between PHASE2 and BOOT2.
SMPS2 Enable Input. The SMPS2 is enabled if EN2 is greater than the logic high level and disabled if EN2 is less than
the logic low level. If EN2 is connected to REF, the SMPS2 starts after the SMPS1 reaches regulation (delay start).
Drive EN2 below 0.8V to clear fault level and reset the fault latches.
SMP2 Power-Good Open-Drain Output. POK2 is low when the SMPS2 output voltage is more than 10% below the
normal regulation point or during soft-start. POK2 is high impedance when the output is in regulation and the soft-start
circuit has terminated. POK2 is low in shutdown.
Low-Noise Mode Control. Connect SKIP# to GND for normal Idle-Mode (pulse-skipping) operation or to VCC for PWM
mode (fixed frequency). Connect to REF or leave floating for ultrasonic skip mode operation.
SMPS2 Output Voltage-Sense Input. Connect to the SMPS2 output. OUT2 is an input to the Constant on-time-PWM
on-time one-shot circuit. It also serves as the SMPS2 feedback input in fixed-voltage mode.
SMPS2 Current-Limit Adjustment. The GND-PHASE1 current-limit threshold is 1/10th the voltage seen at ILIM2 over
a 0.2V to 2V range. There is an internal 5µA current source from VCC to ILIM2. Connect ILIM2 to REF for a fixed
200mV. The logic current limit threshold is default to 100mV value if ILIM2 is higher than VCC - 1V.
Output voltage control for SMPS2. Connect REFIN2 to VCC for fixed 3.3V. Connect REFIN2 to a 3.3V supply for fixed
1.05V. REFIN2 can be used to program SMPS2 output voltage from 0.5V to 2.50V. SMPS2 output voltage is 0V if
REFIN2 < 0.5V.
8
0.100
12 V
25 V
25 V
25 V
IN
IN
IN
IN
ULTRA SKIP MODE
SKIP MODE
PWM MODE
ULTRA SKIP MODE
1.000
Circuit of Figure 62 and Figure 63, no load on LDO, OUT1, OUT2, and REF, V
EN2 = EN1 = VCC, VBYP = 5V, PVCC = 5V, V
otherwise noted. Typical values are at T
10.000
ISL6237
FUNCTION
100
FIGURE 2. V
90
80
70
60
50
40
30
20
10
0
0.001
A
7 V
7 V
7 V
12 V
12 V
= +25°C.
IN
IN
IN
IN
IN
SKIP MODE
PWM MODE
ULTRA SKIP MODE
OUT1
EN_LDO
SKIP MODE
PWM MODE
0.010
= 1.5V EFFICIENCY vs LOAD (200kHz)
= 5V, T
OUTPUT LOAD (A)
A
= -40°C to +100°C , unless
0.100
12 V
25 V
25 V
25 V
IN
IN
IN
IN
ULTRA SKIP MODE
SKIP MODE
PWM MODE
ULTRA SKIP MODE
IN
1.000
= 12V,
March 16, 2007
FN6418.1
10.000