ltc4270 Linear Technology Corporation, ltc4270 Datasheet - Page 14

• Manufacturer Part Number: ltc4270
• Description: 12-port Poe/poe+/ltpoe++ Pse Controller
• Manufacturer: Linear Technology Corporation

PIN FUNCTIONS
LTC4270/LTC4271
LTC4270
SENSEn (Pins 1, 4, 8, 11, 15, 18, 21, 24, 30, 33, 37,
40): Port n Current Sense Input. SENSEn monitors the
external MOSFET current via a 0.5Ω or 0.25Ω sense
resistor between SENSEn and V
across the sense resistor exceeds the overcurrent detection
threshold V
the voltage across the sense resistor reaches the current
limit threshold V
maintain constant current in the external MOSFET. See
Applications Information for further details. If the port is
unused, the SENSEn pin must be tied to V
GATEn (Pins 2, 5, 9, 12, 16, 19, 22, 25, 29, 32, 36, 39):
Port n Gate Drive. GATEn should be connected to the gate
of the external MOSFET for port n. When the MOSFET is
turned on, the gate voltage is driven to 13V (typ) above
V
will be reduced to maintain constant current through the
external MOSFET. If the fault timer expires, GATEn is pulled
down, turning the MOSFET off and recording a port fault
event. If the port is unused, float the GATEn pin.
OUTn (Pins 3, 6, 10, 13, 17, 20, 23, 26, 28, 31, 35, 38):
Port n Output Voltage Monitor. OUTn should be connected
to the output port. A current limit foldback circuit limits
the power dissipation in the external MOSFET by reducing
the current limit threshold when the drain-to-source volt-
age exceeds 10V. The port n Power Good bit is set when
the voltage from OUTn to V
500k resistor is connected internally from OUTn to AGND
when the port is idle. If the port is unused, the OUTn pin
must be floated.
CAP2 (Pin 7): Analog Internal 4.3V Power Supply Bypass
Capacitor. Connect 0.1μF ceramic cap to V
XIO0 (Pin 14): General Purpose Digital Input Output. Logic
signal between V
XIO1 (Pin 27): General Purpose Digital Input Output. Logic
signal between V
14
EE
. During a current limit condition, the voltage at GATEn
CUT
, the current limit fault timer counts up. If
LIM
EE
EE
and V
and V
, the GATEn pin voltage is lowered to
EE
EE
EE
+ 4.3V. Internal pull up.
+ 4.3V. Internal pull up.
drops below 2.4V (typ). A
EE
. Whenever the voltage
EE
EE
.
.
AGND (Pin 34): Analog Ground. Connect AGND to the
return for the V
V
a –45V to –57V supply, relative to AGND. Voltage depends
on PSE type (Type 1, Type 2 or LTPoE ++ .)
DNA (Pin 47): Data Transceiver Negative Input Output
(Analog). Connect to DND through a data transformer.
DPA (Pin 48): Data Transceiver Positive Input Output
(Analog). Connect to DPD through a data transformer.
CNA (Pin 49): Clock Transceiver Negative Input Output
(Analog). Connect to CND through a data transformer.
CPA (Pin 50): Clock Transceiver Positive Input Output
(Analog). Connect to CPD through a data transformer.
VSSK (Exposed Pad Pin 53): Kelvin Sense to V
to sense resistor common node. Do not connect directly
to V
Common Pins
NC, DNC (LTC4271 Pins 7,13; LTC4270 Pins 42, 43, 44,
45, 46): All pins identified with “NC” or “DNC” must be
left unconnected.
LTC4271
AD0 (Pin 1): Address Bit 0. Tie the address pins high or low
to set the starting I
responds. The chip will respond to this address plus the
next two incremental addresses. The base address of the
first four ports will be (A
third groups of four ports will respond at the next two
logical addresses. Internally pulled up to V
AD1 (Pin 2): Address Bit 1. See AD0.
AD2 (Pin 3): Address Bit 2. See AD0.
AD3 (Pin 4): Address Bit 3. See AD0.
AD6 (Pin 5): Address Bit 6. See AD0.
MID (Pin 6): Midspan Mode Input. When high, the LTC4271
acts as a midspan device. Internally pulled down to DGND.
EE
(Pins 41, 51, 52): Main PoE Supply Input. Connect to
EE
plane. See Layout Guide.
EE
supply.
2
C serial address to which the LTC4271
6
10A
3
A
2
A
1
A
0
)b. The second and
DD
.
EE
. Connect
42701f