s29al008d Meet Spansion Inc., s29al008d Datasheet - Page 14

• Manufacturer Part Number: s29al008d
• Description: 8 Megabit 1 M X 8-bit/512 K X 16-bit Cmos 3.0 Volt-only Boot Sector Flash Memory
• Manufacturer: Meet Spansion Inc.

7.
7.1
7.2
14
Device Bus Operations
Word/Byte Configuration
Requirements for Reading Array Data
This section describes the requirements and use of the device bus operations, which are initiated through the
internal command register. The command register itself does not occupy any addressable memory location.
The register is composed of latches that store the commands, along with the address and data information
needed to execute the command. The contents of the register serve as inputs to the internal state machine.
The state machine outputs dictate the function of the device.
inputs and control levels they require, and the resulting output. The following subsections describe each of
these operations in further detail.
Legend
L = Logic Low = V
H = Logic High = V
V
X = Don’t Care
A
D
D
Notes
1. Addresses are A18:A0 in word mode (BYTE# = V
2. The sector protect and sector unprotect functions may also be implemented via programming equipment. See
The BYTE# pin controls whether the device data I/O pins DQ15–DQ0 operate in the byte or word
configuration. If the BYTE# pin is set at logic 1, the device is in word configuration, DQ15–DQ0 are active and
controlled by CE# and OE#.
If the BYTE# pin is set at logic 0, the device is in byte configuration, and only data I/O pins DQ0–DQ7 are
active and controlled by CE# and OE#. The data I/O pins DQ8–DQ14 are tri-stated, and the DQ15 pin is used
as an input for the LSB (A-1) address function.
To read array data from the outputs, the system must drive the CE# and OE# pins to V
control and selects the device. OE# is the output control and gates array data to the output pins. WE# should
remain at V
The internal state machine is set for reading array data upon device power-up, or after a hardware reset. This
ensures that no spurious alteration of the memory content occurs during the power transition. No command is
necessary in this mode to obtain array data. Standard microprocessor read cycles that assert valid addresses
on the device address inputs produce valid data on the device data outputs. The device remains enabled for
read access until the command register contents are altered.
Read
Write
Standby
Output Disable
Reset
Sector Protect
Sector Unprotect
Temporary Sector Unprotect
ID
IN
IN
OUT
Unprotection on page
= 12.0 ± 0.5 V
= Address In
= Data In
= Data Out
Operation
IH
(Note 2)
. The BYTE# pin determines whether the device outputs array data in words or bytes.
(Note 2)
IL
IH
18.
V
0.3 V
CE#
CC
X
X
L
L
L
L
L
Table 7.1 S29AL008D Device Bus Operations
±
OE#
H
X
H
X
H
H
X
L
S29AL008D
WE#
H
X
H
X
X
IH
L
L
L
), A18:A-1 in byte mode (BYTE# = V
D a t a
RESET#
V
0.3 V
V
V
V
CC
H
H
H
L
ID
ID
ID
±
S h e e t
Sector Address,
Sector Address,
A6 = H, A1 = H,
A6 = L, A1 = H,
Addresses
(Note 1)
A0 = L
A0 = L
Table 7.1
A
A
A
X
X
X
IN
IN
IN
S29AL008D_00_A10 November 27, 2007
IL
lists the device bus operations, the
).
High-Z
High-Z
High-Z
DQ0–
D
DQ7
D
D
D
D
OUT
IN
IN
IN
IN
BYTE#
High-Z
High-Z
High-Z
D
= V
D
D
OUT
X
X
IN
IN
IH
IL
. CE# is the power
Sector Protection/
DQ8–DQ15
DQ8–DQ14 = High-Z,
DQ15 = A-1
BYTE#
High-Z
High-Z
High-Z
High-Z
= V
X
X
IL