hi5766 Intersil Corporation, hi5766 Datasheet - Page 13
![no-image](/images/manufacturer_photos/0/3/342/intersil_corporation_sml.jpg)
hi5766
Manufacturer Part Number
hi5766
Description
10-bit, 60msps A/d Converter
Manufacturer
Intersil Corporation
Datasheet
1.HI5766.pdf
(16 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
hi5766KCAZ
Manufacturer:
Intersil
Quantity:
45
Part Number:
hi5766KCB
Manufacturer:
INTERSIL
Quantity:
20 000
Company:
Part Number:
hi5766KCBZ
Manufacturer:
Intersil
Quantity:
52
Company:
Part Number:
hi5766KCBZ
Manufacturer:
Intersil
Quantity:
35
Part Number:
hi5766KCBZ
Manufacturer:
INTERSIL
Quantity:
20 000
The resistors, R, in Figure 26 are not absolutely necessary
but may be used as load setting resistors. A capacitor, C,
connected from V
frequency noise on the inputs, also improving performance.
Values around 20pF are sufficient and can be used on AC
coupled inputs as well. Note, however, that the value of
capacitor C chosen must take into account the highest
frequency component of the analog input signal.
Analog Input, Single-Ended Connection
The configuration shown in Figure 27 may be used with a
single ended AC coupled input.
Again, assume the difference between V
2.5V, and V
sinewave, then V
positive voltage equal to VDC . The converter will be at
positive full scale when V
equal to VDC - 0.5V (V
headroom must be provided such that the input voltage
never goes above +5V or below AGND. In this case, VDC
could range between 0.5V and 4.5V without a significant
change in ADC performance. The simplest way to produce
VDC is to use the DC bias source, V
HI5766.
The single ended analog input can be DC coupled
(Figure 28) as long as the input is within the analog input
common mode voltage range.
= +0.5V) and will be at negative full scale when V
V
IN
FIGURE 27. AC COUPLED SINGLE ENDED INPUT
REF
VDC
-, typically 2V, is 0.5V. If V
IN
IN
+ is a 1V
+ to V
IN
IN
+ - V
IN
+ is at VDC + 0.5V (V
- will help filter any high
P-P
13
IN
R
sinewave riding on a
- = -0.5V). Sufficient
DC
, output of the
REF
IN
V
V
IN
IN
+, typically
is a 1V
HI5766
-
+
IN
IN
+ - V
P-P
+ is
IN
-
HI5766
The resistor, R, in Figure 28 is not absolutely necessary but
may be used as a load setting resistor. A capacitor, C,
connected from V
frequency noise on the inputs, also improving performance.
Values around 20pF are sufficient and can be used on AC
coupled inputs as well. Note, however, that the value of
capacitor C chosen must take into account the highest
frequency component of the analog input signal.
A single ended source may give better overall system
performance if it is first converted to differential before driving
the HI5766.
Digital Output Control and Clock Requirements
The HI5766 provides a standard high-speed interface to
external TTL logic families.
In order to ensure rated performance of the HI5766, the duty
cycle of the clock should be held at 50% ±5%. It must also
have low jitter and operate at standard TTL levels.
Performance of the HI5766 will only be guaranteed at
conversion rates above 1 MSPS. This ensures proper
performance of the internal dynamic circuits. Similarly, when
power is first applied to the converter, a maximum of 20
cycles at a sample rate above 1 MSPS will have to be
performed before valid data is available.
A Data Format Select (DFS) pin is provided which will
determine the format of the digital data outputs. When at
logic low, the data will be output in offset binary format.
When at logic high, the data will be output in two’s
complement format. Refer to Table 1 for further information.
FIGURE 28. DC COUPLED SINGLE ENDED INPUT
VDC
V
IN
VDC
IN
+ to V
IN
- will help filter any high
R
C
V
V
IN
IN
-
HI5766
+