hsdl-3610 Avago Technologies, hsdl-3610 Datasheet
hsdl-3610
Available stocks
Related parts for hsdl-3610
hsdl-3610 Summary of contents
Page 1
... IR data link. The module is compliant to IrDA Data Physical Layer Specifications 1.0 and IEC825-Class 1 Eye Safe. The HSDL-3610 contains a high-speed and high- efficiency 870 nm LED, a silicon PIN diode, and an integrated circuit. The IC contains an LED driver and a receiver providing a single output (RXD) for all data rates supported ...
Page 2
... IrDA link. Ordering Information Package Option 2 The HSDL-3610 comes in two package options; the front view option (HSDL-3610#007/#017), and the top view option (HSDL- 3610#008/#018). Both options come with integrated shield that ...
Page 3
... Mode 0 Mode 1 No Connection Ground Receiver Data Output Transmitter Data Input LED Anode BOTTOM VIEW (HSDL-3610 #008/#018) Outputs RXD Not Valid [2] Low High Not Valid Symbol Vcc AGND GND MD0 MD1 NC GND RXD TXD LEDA ...
Page 4
... Watt, for 4.75 Vcc 5.25 V operation [5] CX1 0.47 F 20%, X7R Ceramic [6] CX2 6.8 F 20%, Tantalum Notes: 4. CX1 must be placed within 0 the HSDL-3610 to obtain optimum noise immunity environments with noisy power supplies, supply rejection performance can be enhanced by including CX2, as shown in “HSDL-3610 Functional Block Diagram” in page 3. 0.7 0.6 0.5 0.4 0.3 ...
Page 5
Absolute Maximum Ratings Parameter Storage Temperature Operating Temperature DC LED Current Peak LED Current LED Anode Voltage Supply Voltage Transmitter Data I Input Current Receiver Data Output Voltage Note: 6. For implementations where case to ambient thermal resistance 50 ...
Page 6
Electrical & Optical Specifications Specifications hold over the Recommended Operating Conditions unless otherwise noted. Unspecified test conditions can be anywhere in their operating range. All typical values are and 3.3 V unless otherwise noted. Parameter Transceiver Supply ...
Page 7
Electrical & Optical Specifications Specifications hold over the Recommended Operating Conditions unless otherwise noted. Unspecified test conditions can be anywhere in their operating range. All typical values are and 3.3 V unless otherwise noted. Parameter Receiver [8] ...
Page 8
RXD Output Waveform V OH 90% 50% 10 LED Optical Waveform LED ON 90% 50% 10% LED OFF t r Receiver Wake Up Time Definition (when MD0 1 and MD1 0) RX LIGHT RXD t w ...
Page 9
... HSDL-3610#007 and HSDL3610#017 Package Outline with Dimension and Recommended PC Board Pad Layout HSDL-3610#007/#017 (Front Option) PIN FUNCTION PIN FUNCTION AGND 7 GND 3 GND 8 RXD 4 MD0 9 TXD 5 MD1 10 LEDA 2.55 0.80 1.20 4.05 SIDE VIEW ALL DIMENSIONS IN MILLIMETERS (mm). DIMENSION TOLERANCE IS 0.20 mm UNLESS OTHERWISE SPECIFIED. ...
Page 10
... HSDL-3610#008 and HSDL3610#018 Package Outline with Dimension and Recommended PC Board Pad Layout HSDL-3610#008/#018 (Top Option) PIN FUNCTION PIN FUNCTION AGND 7 GND 3 GND 8 RXD 4 MD0 9 TXD 5 MD1 10 LEDA LEGEND: MC – MOUNTING CENTER OC – OPTICAL CENTER 2.40 1.50 2.25 SIDE VIEW ALL DIMENSIONS IN MILLIMETERS (mm). ...
Page 11
... SHAPE AND DIMENSIONS OF REELS 4.00 ± 0.10 2.00 ± 0.10 + 0.10 1.50 0 POLARITY A 12.40 ± 0. 5.50 ± 0.10 0.40 ± 0.05 4.20 ± 0.10 DIRECTION OF PULLING 11 Quantity = 400 pieces per reel (HSDL-3610#007) (40 mm MIN.) EMPTY 2.00 ± 0.50 DIRECTION OF PULLING 1.75 ± 0.10 11.50 ± 0.10 24.00 ± 0.20 8.00 ± 0.10 TAPE DIMENSIONS = 10 pieces per tape (HSDL-3610#017) (400 mm MIN.) PARTS LEADER MOUNTED EMPTY (40 mm MIN ...
Page 12
... SHAPE AND DIMENSIONS OF REELS 4.00 ± 0.10 2.00 ± 0.10 1.50 + 0.10 POLARITY V DD 12.80 ± 0.10 A 4.80 ± 0.10 0.40 ± 0.05 5.65 ± 0.10 5.10 ± 0.10 DIRECTION OF PULLING 12 Quantity = 400 pieces per reel (HSDL-3610#008) (40 mm MIN.) EMPTY 2.00 ± 0.50 DIRECTION OF PULLING 1.75 ± 0.10 11.50 ± 0.10 24.00 ± 0.20 5.30 ± 0.10 8.00 ± 0.10 TAPE DIMENSIONS = 10 pieces per tape (HSDL-3610#018) (400 mm MIN.) PARTS LEADER ...
Page 13
... Moisture Proof Packaging All HSDL-3610 options are shipped in moisture proof package. Once opened, moisture absorption begins. UNITS IN A SEALED MOISTURE-PROOF PACKAGE PACKAGE IS OPENED (UNSEALED) ENVIRONMENT LESS THAN 25°C, AND LESS THAN 60% RH? NO PACKAGE IS OPENED MORE THAN 3 DAYS? YES PERFORM RECOMMENDED BAKING CONDITIONS ...
Page 14
... The cool down rate, R5, from the liquidus point of the solder (77 F) should not exceed -3 C per second maximum. This limitation is necessary to allow the PC board and HSDL-3610 castellation I/O pins to change dimensions evenly, putting minimal stresses on the HSDL-3610 transceiver. ...
Page 15
Appendix A: Test Method A1. Background Light and Electromagnetic Field There are four ambient interference conditions in which the receiver is to operate correctly. The conditions are to be applied separately: 1. Electromagnetic field: 3 V/m maximum (please refer to ...
Page 16
... Appendix B: HSDL-3610#007/#017 SMT Assembly Application Note 1.0 Solder Pad, Mask and Metal Solder Stencil Aperture STENCIL APERTURE SOLDER MASK Figure 1.0. Stencil and PCBA. 1.1 Recommended Land Pattern for HSDL-3610#007/#017 Dim. mm Inches a 2.40 0.095 b 0.70 0.028 c (pitch) 1.10 0.043 d 2.35 0.093 e 2.80 0.110 f 3.13 0.123 g 4.31 0.170 16 METAL STENCIL ...
Page 17
... Note: Wet/Liquid Photo-Imaginable solder resist/mask is recommended LENS LAND h Y Figure 3.0. HSDL-3610#007/#017 PCBA – Adjacent land keep-out and solder mask. Rx LENS k SOLDER MASK l ...
Page 18
Recommended Metal Solder Stencil Aperture It is recommended that only 0.152 mm (0.006 inches) or 0.127 mm (0.005 inches) thick stencil be used for solder paste printing. t, nominal stencil thickness mm 0.152 0.127 w, the width of aperture ...
Page 19
Tolerance for X-axis Alignment of Castellation Misalignment of castellation to the land pad should not exceed 0 approximately half the width of the castellation during Photo 1.0. Castellation misaligned to land pads in x-axis before reflow. 3.2 ...
Page 20
... It is recommended that the unit be placed in line with the fiducial LENS MINIMUM 1/2 THE LENGTH OF THE LAND PAD Y Figure 5.0. Section of a castellation in Y-axis. 3.4 Example of Good HSDL-3610#007/#017 Castellation Solder Joints Photo 5.0. Good solder joint. 20 mark (mid-length of land pad.) This will enable sufficient land 1 ...
Page 21
... Solder Volume Evaluation and Calculation Geometry of an HSDL-3610#007/#017 solder fillet. 0.8 0.4 21 0.425 1.2 0.7 0.20 0.70 ...
Page 22
... Appendix C : HSDL-3610#008/#018 SMT Assembly Application Note 1.0 Solder Pad, Mask and Metal Solder Stencil Aperture STENCIL APERTURE SOLDER MASK Figure 1.0. Stencil and PCBA. 1.1 Recommended Land Pattern for HSDL-3610#008/#018 Dim. mm Inches a 1.95 0.077 b 0.60 0.024 c (pitch) 1.10 0.043 d 1.60 0.063 e 5.70 0.224 f 3.80 0.150 g 2.40 0.094 h 0.80 0.032 22 METAL STENCIL ...
Page 23
... Note: Wet/Liquid Photo-Imaginable solder resist/mask is recommended LENS LAND h Y Figure 3.0. HSDL-3610#008/#018 PCBA – Adjacent land keep-out and solder mask. Tx LENS k SOLDER MASK l ...
Page 24
Recommended Metal Solder Stencil Aperture It is recommended that only 0.152 mm (0.006 inches) or 0.127 mm (0.005 inches) thick stencil be used for solder paste printing. t, nominal stencil thickness mm 0.152 0.127 w, the width of aperture ...
Page 25
Tolerance for X-axis Alignment of Castellation Misalignment of castellation to the land pad should not exceed 0 approximately half the width of the castellation during Solder Castellation Photo 1.0. Castellation mis-aligned to land pads in X-axis before ...
Page 26
Y-axis Misalignment of Castellation In the Y-direction, the unit does not self align after solder reflow recommended that the unit be placed in line with the fiducial mark. This will enable sufficient land length to form a ...
Page 27
... Solder Volume Evaluation and Calculation Geometry of an HSDL-3610#008/#018 solder fillet. 0.46 0.6 0.1 0 (0.8 x 0.6 x 0.1) + (0.5 x 0.6 x 0.46 (0.6 + 1.15)/2) = 0.1662 mm solder /0.6 = 0.277 mm paste solder 27 0.6 1.15 3 ...
Page 28
... For product information and a complete list of distributors, please go to our website: Avago, Avago Technologies, and the A logo are trademarks of Avago Technologies, Pte. in the United States and other countries. Data subject to change. Copyright © 2006 Avago Technologies Pte. All rights reserved. Obsoletes 5980-1767E 5988-2314EN April 20, 2006 www ...