m27c801 STMicroelectronics, m27c801 Datasheet - Page 8

no-image

m27c801

Manufacturer Part Number
m27c801
Description
8 Mbit 1mb X 8 Uv Eprom And Otp Eprom
Manufacturer
STMicroelectronics
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
M27C801
Manufacturer:
ST
0
Part Number:
m27c801-100
Manufacturer:
ST
0
Part Number:
m27c801-100 F1
Manufacturer:
ST
0
Part Number:
m27c801-100B1
Manufacturer:
ST
Quantity:
53
Part Number:
m27c801-100B1
Manufacturer:
ICS
Quantity:
6 107
Part Number:
m27c801-100B1
Manufacturer:
ST
Quantity:
1 000
Part Number:
m27c801-100B1
Manufacturer:
ST
0
Part Number:
m27c801-100B1
Manufacturer:
ST
Quantity:
20 000
Part Number:
m27c801-100F1
Manufacturer:
AIC
Quantity:
63 000
Part Number:
m27c801-100F1
Manufacturer:
ST
Quantity:
6 100
Part Number:
m27c801-100F1
Manufacturer:
ST
Quantity:
6 100
Part Number:
m27c801-100F1
Manufacturer:
ST
Quantity:
20 000
Part Number:
m27c801-100F1
Manufacturer:
ST/意法
Quantity:
330
Device description
2
2.1
2.2
2.3
8/24
Device description
The operating modes of the M27C801 are listed in the Operating Modes table. A single
power supply is required in Read mode. All inputs are TTL levels except for GV
on A9 for Electronic Signature and Margin Mode Set or Reset.
Table 2.
1. X = V
Read mode
The M27C801 has two control functions, both of which must be logically active in order to
obtain data at the outputs. Chip Enable (E) is the power control and should be used for
device selection. Output Enable (G) is the output control and should be used to gate data to
the output pins, independent of device selection. Assuming that the addresses are stable,
the address access time (t
available at the output after a delay of t
been low and the addresses have been stable for at least t
Standby mode
The M27C801 has a standby mode which reduces the supply current from 35mA to 100µA.
The M27C801 is placed in the standby mode by applying a CMOS high signal to the E input.
When in the standby mode, the outputs are in a high impedance state, independent of the
GV
Two-line output control
Because EPROMs are usually used in larger memory arrays, the product features a 2 line
control function which accommodates the use of multiple memory connection. The two line
control function allows:
For the most efficient use of these two control lines, E should be decoded and used as the
primary device selecting function, while G should be made a common connection to all
devices in the array and connected to the READ line from the system control bus. This
Read
Output Disable
Program
Program Inhibit
Standby
Electronic signature
PP
the lowest possible memory power dissipation,
complete assurance that output bus contention will not occur.
input.
IH
or V
Mode
Operating modes
IL
, V
ID
= 12 V ± 0.5 V.
AVQV
) is equal to the delay from E to output (t
(1)
V
IL
V
V
V
V
V
Pulse
E
IH
IH
IL
IL
IL
GLQV
from the falling edge of G, assuming that E has
GV
V
V
V
V
V
X
PP
PP
IH
IL
IL
pp
AVQV
-t
GLQV
V
A9
X
X
X
X
X
ID
.
ELQV
). Data is
PP
Data Out
Data In
Q7-Q0
Codes
M27C801
and 12V
Hi-Z
Hi-Z
Hi-Z

Related parts for m27c801