sc60021rm Staco Energy Products Co., sc60021rm Datasheet

Page 1

... UniStar P Series 6kVA Rack/Universal Mount Parallel Redundancy/Capacity 003-2284 Rev C Models: SC60021RM SC60022RM On-Line UPS User’s Manual 1/5/09 ...

Page 2

Important Safety Instruction 1.1. An Important Notice 1.2. Storage Instruction 2 Product Introduction 2.1. General Characteristics 2.2. Symbols on the LCD Display Panel 2.3. Panel explanation 2.4. Communication Port Explanation 3 Installation and Operation 3.1. Unpacking .......................................................................................................... 12 3.2. ...

Page 3

Important Safety Instruction 1.1. An Important Notice For Parallel System installation, please refer to Parallel System Installation Guide Part number 003-2302 Because of “small leakage currents” generated by the EMI filter of the UPS necessary to insure ...

Page 4

Install the UPS indoors not designed for installation outdoors. Dusty, corrosive and salty environments can do damage to any UPS. Install the UPS away from objects that give off excessive heat and areas that are excessively wet. ...

Page 5

SAVE THESE INSTRUCTIONS - This Manual Contains Important Instructions that should be Followed during Installation and Maintenance of the UPS and Batteries. ...

Page 6

Product Introduction 2.1. General Characteristics True online architecture continuously supplies in your critical device with a stable, regulated, transient-free pure sine wave AC Power. 20KHz PWM sine-wave topology yields an excellent overall performance. High crest factor capability of the ...

Page 7

Providing four different working modes, such as Normal, ECO, CF50 and CF60, it may widely be used in a variety of applications. DC-start function allows the UPS to be started during power outages. Revolutionary battery management circuit analyzes battery discharging ...

Page 8

Symbols on the LCD Display Panel Item Symbol 2.2.1.1 2.2.1 OFF 9 LINE Utility or Bypass Source LINE UPS Working in specified mode* A ...

Page 9

EPO 25 26 Er05 27 Er06 28 Er10 29 Er11 30 Er12 31 Er15 32 Er24 33 Er** *The specified modes include Normal mode, ECO mode, CVCF mode, etc.. Next Page Special ...

Page 10

Panel explanation Front Panel Function Explanations LCD Display Green LED steadily lights up to indicate that the utility input voltage is within the window Green LED lights up to indicate Bypass Input is normal. Green LED lights up to ...

Page 11

Rear Panel Explanation A Terminal Resistor for Parallel function B RS232 Port C External Battery Connector D Utility Input Breaker E CAN Bus Connection Port for Parallel System F Maintenance Bypass Switch and Galvanic Tx. Temperature Sensor G Cooling Fan ...

Page 12

Communication Port Explanation The Communication port on the UPS provides RS232 protocol to communicate with UPS software for remote monitoring. Available optional interfaces cards, which contains R2E (2 (RS485), USE (USB), DCE (Dry Contact), as well as SNMP/ card, ...

Page 13

Installation and Operation The packing material and the external condition of the unit should be inspected carefully before installation. Retain the packing material for future use. 3.1. Unpacking Take the UPS out of the PE foam. Unwrap the UPS. ...

Page 14

Selecting Installation Position It is necessary to select a proper environment to install the unit, in order to minimize the possibility of damage to the UPS and extend the life of the UPS. Please follow the advice below: 1. ...

Page 15

Installation of Casters Cover Tower installation step 3.3.1.1 Power Module + Battery Module Step 1 Installation: Foot Cover and Power Module S3 Step 2 Installation: Power Module and Battery Module ...

Page 16

Power Module+ Isolation Transformer Module+ Battery Module Step 1 Installation: Power, Isolation Transformer and Battery Module S3 Rack installation step 3.3.1.3 Power Module+ Battery Module Step 1 Installation: Ear Cover ...

Page 17

Step 2 Installation: Ear Cover to Power, Isolation Transformer and Battery Module S3 Step 3 Installation: Rail to Rack S3 16 ...

Page 18

Step 4 Installation: Battery Module to Rail 3.3.1.4 Power Module+ Isolation Transformer Module+ Battery Module Step 1 Installation: Isolation Transformer Module to Rail 17 ...

Page 19

Step 2 Installation: Power Module to Rack 18 ...

Page 20

Terminal Block Explanation L12-N1: Utility Input power when the UPS is running in Utility mode. ● G1: UPS Input Ground. ● L21、N22: UPS Output. ● G2: UPS Output Ground. ● Remarks: 1. When the Isolation transformer and Maintenance Bypass ...

Page 21

Operation Test and Installation Instruction Start Up in Normal Mode 3.5.1.1 Open the terminal block cover on the rear panel (refer to 0). Before installation make sure the unit is properly grounded. Make sure Utility breaker, UPS’ Utility breaker ...

Page 22

The UPS performs another self-test and the LCD display will change from drawing C to drawing D, running in battery mode for approx. 4 seconds, then the display will change from drawing E1 to drawing F if the self-test ...

Page 23

Start-up operation of the UPS is completely now. Make sure the UPS is plugged onto the wall receptacle for charging at least 8 hours and the batteries of the UPS are fully charged. Start-up in Battery Mode (Cold Start) ...

Page 24

Check Measured Values & Figures detected by UPS 3.5.1.13 If you would like to check the operating parameters of the UPS, use the scroll down key pad, the LCD display will illustrate as Drawing C(Voltage from Utility Input) Drawing I1(Voltage ...

Page 25

L * Display shows UPS output Voltage Display shows UPS output frequency Display shows UPS output load level(%) O * Display shows Battery Voltage Display shows UPS Inner Temperature 24 ...

Page 26

UPS Default Data and Special Function Execution 3.5.1.14 After UPS completely starts up, press display screen to drawing Q1 Display shows alarm (b for buzzer) “On” shows buzzer “Off” * Display shows alarm (b for ...

Page 27

26 ...

Page 28

R2 * Display shows self-test is “On” Display shows Bypass Voltage is adjusted to narrow one Display shows bypass voltage is adjusted to wider one Display shows Frequency Window is +/-3Hz Display ...

Page 29

V1 * Display shows the UPS is operated in “normal mode” Display shows the UPS is operated in “Eco mode” Display shows the UPS is operated in “CVCF 50Hz mode” Display shows the UPS ...

Page 30

X * Display shows UPS Identification Number Display shows the UPS is in position No parallel system. 3.5.1.18 Press scroll up Functions includes alarm/buzzer ON (as drawing Q1), or alarm/buzzer OFF (as drawing Q2, Alarm ...

Page 31

UPS Default Settings and their alternatives 3.5.1.19 Make sure the UPS is OFF. Press On Switch key pads simultaneously for approx. 3 seconds, the alarm will sound twice, the LCD display screen shows as drawing Q1. The UPS is now ...

Page 32

Turn Off the Utility power to the UPS Input. 3.5.1.30 Your Setting changes are complete. UPS Is Off Due to Unknown Reason and Its Trouble Shooting 3.5.1. serious abnormal condition has occurred, the UPS will lock it ...

Page 33

Maintenance Bypass Mode 3.5.1.37 Maintenance Bypass Mode is intended for UPS maintenance only. The following procedure must be performed by an authorized, trained service technician. If there is any damage caused by failure to follow this procedure or unauthorized use ...

Page 34

Troubleshooting Guide 4.1. Trouble Shooting When the UPS malfunctions during operation, you may check the followings the input and output power wiring correct the Utility voltage within the input window of the UPS? In case ...

Page 35

Situation UPS Red Fault LED lights up UPS fails to offer battery backup or its back up time is shorter than its calculation. UPS locks itself and it can not be turned off. Check Items Check the error code shown ...

Page 36

Bundled Software Installation Guide 5.1. Hardware Installation 1. Connect the male connector of RS232 cable to the UPS communication port. 2. Connect the female connector of the RS232 cable to a dedicated RS232 port of the computer. 3. For ...

Page 37

Customer Options Slots 6.1. All the below interface cards are with built-in EPO function. The pin assignments of the EPO are enable the EPO function, please short Pin 1 & 2. 6.2. R2E (2nd RS-232 ) ...

Page 38

USE (USB) card CN1 for USB and CN3 for EPO. For communication protocol, please see the definition below: Comply with USB version 1.0,1.5Mbps Comply with USB HID Version 1.0. The Pin Assignments of the USE card: Installation Position: slot1 ...

Page 39

The shutdown function will be activated, after a +6~+25Vdc is connected between pin 9 and pin10 for 5 seconds. The capacity of each relay contact is 40Vdc/25mA. Installation Position: slot1(CHA-CN7) or slot 2(CHB-CN8). Flexible signal output for N.C.(Normally closed) or ...

Page 40

SNMP Cards SNMP/WEB card For installation, please refer to the user’s manual attached with the card. . Installation Position: slot1 or slot 2. Adapted flat cable: cable A or cable B For installation, please refer to Chapter 6.7 Net ...

Page 41

...

Page 42

Hot Swappable Battery Replacement 1. Unscrew the flank of the battery bank front panel as indicated in Step 1. 2. Remove the front panel as indicated in Step 2. 3. Remove the screw of the battery pack as shown ...

Page 43

Remove the battery packs from the battery bank as shown in Step 5. 42 ...

Page 44

... PHYSICAL Input Connection Output Connection Dimensions ( inches Weight (lbs.) Listing EXTERNAL BATTERY PACK – Module 2 SC60021RM Single, Line + Neutral + Ground Up to 0.99 at 100% Linear Load <5% at 100% Linear Load Hardwire 208/120Vac or 240/120Vac +/- 0%; +/- 1%; +/- 2%; +/- 3% Sine Wave, THD < 3% (no load to full load) +/- 0.2% (Free Running) < ...

Page 45

Battery Run Time @ Full Load Type Hot – Swap Batteries Recharge Time Battery Connection Extended Run Time Battery Packs Dimensions ( Weight (lbs.) *OUTPUT TRANSFORMER / MANUAL BYPASS - Module 3 (Hardwired to UPS ...

Page 46

... User shall contact Staco Field Services at 1-866-261-1191. Subject to the limitations specified herein, nonconforming may be returned to Staco for repair or replacement, at Staco’s discretion, without charge for material or labor. All returns must be shipped freight prepaid to Staco Energy products Co. Staco will pay freight charges from factory to customer domestic (US and Canada) location. In the event that the nonconforming unit is not returned, User may be billed for new unit replacement cost ...

Page 47

... International: Staco Energy Products Co. (Staco), Dayton, Ohio, warrants this equipment, with all applicable terms and conditions stated above free of defects in material and workmanship for a period of one year from the installation date, no more than eighteen (18) months from shipment date from a Staco warehouse ...

Page 48

... Staco Energy Products Co. 301 Gaddis Blvd. Dayton, OH 45403 US Toll Free: 866.261.1191 Fax: 937.253.1723 www.stacoenergy.com 003-284 47 ...