lx64eb Lattice Semiconductor Corp., lx64eb Datasheet - Page 22

• Manufacturer Part Number: lx64eb
• Description: High Performance Interfacing And Switching
• Manufacturer: Lattice Semiconductor Corp.

Lattice Semiconductor
Absolute Maximum Ratings
Supply Voltage V
PLL Supply Voltage V
Output Supply Voltage V
JTAG Supply Voltage (V
Input or I/O Tristate Voltage Applied
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . -65 to 150°C . . . . . . . . . . . . . . . -65 to 150°C
Junction Temp. (T
1. Stress above those listed under the Absolute Maximum Ratings may cause permanent damage to the device. Functional operation of the
2. Compliance with the Lattice Thermal Management document is required.
3. All voltages referenced to GND.
4. Overshoot and undershoot of -2V to (V
5. A maximum of 64 I/Os per device with V
Recommended Operating Conditions
Erase Reprogram Specifications
Hot Socketing Specifications
V
V
V
T
T
1. sysHSI specification is valid for V
Erase/Reprogram Cycle
Note: Valid over commercial temperature range.
I
1. Insensitive to sequence of V
2. LVTTL, LVCMOS only.
3. 0 < V
4. I
DK
J
J
CC
CCP
CCJ
Symbol
device at these or any other conditions above those indicated in the operational sections of this specification is not implied (while program-
ming, following the programming specifications).
(COM)
(IND)
4
DK
Symbol
is additive to I
CC
≤ V
Input or Tristated I/O Leakage Current
CC
(MAX), 0 < V
CC
Supply Voltage for 1.8V Devices
Supply Voltage for 2.5V Devices
Supply Voltage for 3.3V Devices
Supply Voltage for PLL and sysHSI Blocks, 1.8V Devices
Supply Voltage for PLL and sysHSI Blocks, 2.5V Devices
Supply Voltage for PLL and sysHSI Blocks, 3.3V Devices
Power Supply Voltage for JTAG Programming 1.8V Operation
Power Supply Voltage for JTAG Programming 2.5V Operation
Power Supply Voltage for JTAG Programming 3.3V Operation
Junction Commercial Operation
Junction Industrial Operation
PU
J
) with Power Applied . . . . . . . . -55 to 150°C . . . . . . . . . . . . . . . -55 to 150°C
, I
. . . . . . . . . . . . . . . . . . . . . . . . -0.5 to 2.5V . . . . . . . . . . . . . . . . -0.5 to 5.5V
PD
CCP
or I
CCJ
CCO
Parameter
. . . . . . . . . . . . . . . . . . . . -0.5 to 2.5V . . . . . . . . . . . . . . . . -0.5 to 5.5V
CCO
CC
BH
) . . . . . . . . . . . . . . . . . -0.5 to 4.5V . . . . . . . . . . . . . . . . -0.5 to 4.5V
. Device defaults to pull-up until fuse circuitry is active.
and V
. . . . . . . . . . . . . . . . . -0.5 to 4.5V . . . . . . . . . . . . . . . . -0.5 to 4.5V
CC
≤ V
and V
CCO
CCO
IH
IN
(MAX)+2) volts is permitted for a duration of <20ns.
(MAX).
4, 5
. However, assumes monotonic rise/fall rates for V
> 3.6V is allowed.
CCP
Parameter
. . . . . . . . . -0.5 to 5.5V . . . . . . . . . . . . . . . . -0.5 to 5.5V
= 1.7V to 1.9V.
1, 2, 3
1, 2, 3
Parameter
1
ispGDX2C (1.8V)
0 ≤ V
IN
22
≤ 3.0V
Condition
1
CC
ispGDX2B/V (2.5/3.3V)
ispGDX2 Family Data Sheet
and V
Min
—
CCO,
Min.
1.65
1.65
1.65
-40
2.3
2.3
2.3
3
3
3
0
provided (V
+/-50
1,000
Typ
Min
Max.
1.95
1.95
1.95
105
IN
2.7
3.6
2.7
3.6
2.7
3.6
90
+/-800
Max
- V
Max
—
CCO
) ≤ 3.6V.
Units
Cycles
Units
Units
°
°
V
V
V
V
V
V
V
V
V
μA
C
C