atmega3250v-8auatmega325v-8ai ATMEL Corporation, atmega3250v-8auatmega325v-8ai Datasheet - Page 234
![no-image](/images/manufacturer_photos/0/0/79/atmel_corporation_sml.jpg)
atmega3250v-8auatmega325v-8ai
Manufacturer Part Number
atmega3250v-8auatmega325v-8ai
Description
Atmega3250 8-bit Microcontroller With In-system Programmable Flash
Manufacturer
ATMEL Corporation
Datasheet
1.ATMEGA3250V-8AUATMEGA325V-8AI.pdf
(362 pages)
- Current page: 234 of 362
- Download datasheet (7Mb)
Table 25-5.
Note:
234
Signal Name
NEGSEL_2
NEGSEL_1
NEGSEL_0
PASSEN
PRECH
SCTEST
ST
VCCREN
1. Incorrect setting of the switches in
ATmega325/3250/645/6450
choices to the S&H circuitry on the negative input of the output comparator in
selected from either one ADC pin, Bandgap reference source, or Ground.
Boundary-scan Signals for the ADC
Direction as seen
from the ADC
Input
Input
Input
Input
Input
Input
Input
Input
If the ADC is not to be used during scan, the recommended input values from
be used. The user is recommended not to use the differential amplifier during scan. Switch-Cap
based differential amplifier require fast operation and accurate timing which is difficult to obtain
when used in a scan chain. Details concerning operations of the differential amplifier is therefore
not provided.
The AVR ADC is based on the analog circuitry shown in
mation algorithm implemented in the digital logic. When used in Boundary-scan, the problem is
usually to ensure that an applied analog voltage is measured within some limits. This can easily
be done without running a successive approximation algorithm: apply the lower limit on the digi-
tal DAC[9:0] lines, make sure the output from the comparator is low, then apply the upper limit
on the digital DAC[9:0] lines, and verify the output from the comparator to be high.
The ADC need not be used for pure connectivity testing, since all analog inputs are shared with
a digital port pin as well.
When using the ADC, remember the following
•
•
•
The port pin for the ADC channel in use must be configured to be an input with pull-up
disabled to avoid signal contention.
In Normal mode, a dummy conversion (consisting of 10 comparisons) is performed when
enabling the ADC. The user is advised to wait at least 200ns after enabling the ADC before
controlling/observing any ADC signal, or perform a dummy conversion before using the first
result.
The DAC values must be stable at the midpoint value 0x200 when having the HOLD signal
low (Sample mode).
Description
Input Mux for negative input for differential
signal, bit 2
Input Mux for negative input for differential
signal, bit 1
Input Mux for negative input for differential
signal, bit 0
Enable pass-gate of differential amplifier.
Precharge output latch of comparator.
(Active low)
Switch-cap TEST enable. Output from
differential amplifier send out to Port Pin
having ADC_4
Output of differential amplifier will settle
faster if this signal is high first two ACLK
periods after AMPEN goes high.
Selects Vcc as the ACC reference voltage.
Figure 25-9
(1)
(Continued)
will make signal contention and may damage the part. There are several input
Recommended
Input when not
in use
0
0
0
1
1
0
0
0
Figure
Figure 25-9
25-9. Make sure only one path is
Output Values when
recommended inputs are used,
and CPU is not using the ADC
with a successive approxi-
Table 25-5
0
0
0
1
1
0
0
0
2570L–AVR–08/07
should
Related parts for atmega3250v-8auatmega325v-8ai
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ATMEGA3250V-8AU](/photos/6/70/67048/313-100-tqfp_tmb.jpg)
Part Number:
Description:
IC AVR MCU 32K 8MHZ 100TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA3250V-8AI](/photos/6/70/67048/313-100-tqfp_tmb.jpg)
Part Number:
Description:
IC AVR MCU 32K 8MHZ 100TQFP
Manufacturer:
Atmel
Datasheet:
![ATMEGA3250V-8AUR](/images/manufacturer_photos/0/0/78/atmel_tmb.jpg)
Part Number:
Description:
MCU AVR 32K FLASH 8MHZ 100TQFP
Manufacturer:
Atmel
Datasheet:
![U641B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
![U4082B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
![U4255BM-M](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
![U4089B-P](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
![TDA4470](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet:
![ATF22V10B-25PC](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
High-performance EE PLD
Manufacturer:
ATMEL Corporation
Datasheet:
![AT89C51ED2-IM](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
8-bit Flash Microcontroller
Manufacturer:
ATMEL Corporation
Datasheet:
![AT24C01](/images/manufacturer_photos/0/0/79/atmel_corporation_tmb.jpg)
Part Number:
Description:
2-Wire Serial EEPROM
Manufacturer:
ATMEL Corporation
Datasheet: