xr16m2752 Exar Corporation, xr16m2752 Datasheet - Page 17

no-image

xr16m2752

Manufacturer Part Number
xr16m2752
Description
High Performance Duart With 64-byte Fifo
Manufacturer
Exar Corporation
Datasheet

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
xr16m2752IJ44-F
Manufacturer:
Exar Corporation
Quantity:
10 000
Part Number:
xr16m2752IL32-F
Manufacturer:
EXAR/艾科嘉
Quantity:
20 000
REV. 1.0.0
When software flow control is enabled
data characters with the programmed Xon or Xoff-1,2 character value(s). If receive character(s) (RX) match the
programmed values, the M2752 will halt transmission (TX) as soon as the current character has completed
transmission. When a match occurs, the Xoff (if enabled via IER bit-5) flag will be set and the interrupt output
pin will be activated. Following a suspension due to a match of the Xoff character, the M2752 will monitor the
receive data stream for a match to the Xon-1,2 character. If a match is found, the M2752 will resume operation
and clear the flags (ISR bit-4).
Reset initially sets the contents of the Xon/Xoff 8-bit flow control registers to 0x00. Following reset the user can
write any Xon/Xoff value desired for software flow control. Different conditions can be set to detect Xon/Xoff
characters
selected, the M2752 compares two consecutive receive characters with two software flow control 8-bit values
(Xon1, Xon2, Xoff1, Xoff2) and controls TX transmissions accordingly. Under the above described flow control
mechanisms, flow control characters are not placed (stacked) in the user accessible RX data buffer or FIFO.
In the event that the receive buffer is overfilling and flow control needs to be executed, the M2752
automatically sends an Xoff message via the serial TX output to the remote modem. The M2752 sends the
Xoff-1,2 characters two-character times (= time taken to send two characters at the programmed baud rate)
after the receive FIFO crosses the programmed trigger level (for all trigger tables). To clear this condition, the
M2752 will transmit the programmed Xon-1,2 characters as soon as receive FIFO is less than one trigger level
below the programmed trigger level (for Trigger Tables A, B, and C) or when receive FIFO is less than the
trigger level minus the hysteresis value (for Trigger Table D). This hysteresis value is the same as the Auto
RTS Hysteresis value in
selected.
* After the trigger level is reached, an xoff character is sent after a short span of time (= time required to send 2
A special character detect feature is provided to detect an 8-bit character when bit-5 is set in the Enhanced
Feature Register (EFR). When this character (Xoff2) is detected, it will be placed in the FIFO along with normal
incoming RX data.
The M2752 compares each incoming receive character with Xoff-2 data. If a match exists, the received data
will be transferred to FIFO and ISR bit-4 will be set to indicate detection of special character. Although the
Internal Register Table shows Xon, Xoff Registers with eight bits of character information, the actual number of
bits is dependent on the programmed word length. Line Control Register (LCR) bits 0-1 defines the number of
character bits, i.e., either 5 bits, 6 bits, 7 bits, or 8 bits. The word length selected by LCR bits 0-1 also
determines the number of bits that will be used for the special character comparison. Bit-0 in the Xon, Xoff
Registers corresponds with the LSB bit for the receive character.
characters); for example, after 2.083ms has elapsed for 9600 baud and 10-bit word length setting.
2.16
2.17
RX T
Auto Xon/Xoff (Software) Flow Control
RIGGER
Special Character Detect
16
24
28
(See Table
8
L
EVEL
15) and suspend/resume transmissions. When double 8-bit Xon/Xoff characters are
INT P
Table
T
ABLE
IN
A
16
24
28
8
CTIVATION
14.
6: A
1.62V TO 3.63V HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
Table 6
UTO
(See Table
X
ON
below explains this when Trigger Table-B (See
X
/X
(
OFF
CHARACTERS IN RX FIFO
OFF
15), the M2752 compares one or two sequential receive
C
17
(S
HARACTER
OFTWARE
16*
24*
28*
8*
(
S
) S
) F
ENT
LOW
)
C
ONTROL
X
(
CHARACTERS IN RX FIFO
ON
C
HARACTER
16
24
0
8
XR16M2752
(
S
) S
Table
ENT
)
10) is

Related parts for xr16m2752