xr16m752im48 Exar Corporation, xr16m752im48 Datasheet - Page 34
![no-image](/images/manufacturer_photos/0/2/243/exar_corporation_sml.jpg)
xr16m752im48
Manufacturer Part Number
xr16m752im48
Description
Xr68m752 -high Performance Duart With 64-byte Fifo
Manufacturer
Exar Corporation
Datasheet
1.XR16M752IM48.pdf
(51 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
xr16m752im48-F
Manufacturer:
Exar Corporation
Quantity:
10 000
Part Number:
xr16m752im48-F
Manufacturer:
EAXR
Quantity:
20 000
XR16M752/XR68M752
HIGH PERFORMANCE DUART WITH 64-BYTE FIFO
This is a 8-bit general purpose register for the user to store temporary data. The content of this register is
preserved during sleep mode but becomes 0xFF (default) after a reset or a power off-on cycle. There are also
two other registers (TLR and FIFO Rdy) that share the same address location as the Scratch Pad Register.
See
This register replaces MSR and is accessible only when MCR[6] = 1. This 8-bit register is used to store the RX
FIFO threshold levels to halt/resume transmission during hardware or software flow control.
TCR[3:0]: RX FIFO Halt Level
A value of 0-60 (decimal value of TCR[3:0] multiplied by 4) can be selected as the Halt Level. When the RX
FIFO is greater than or equal to this value, the RTS# output will be de-asserted if Auto RTS flow control is used
or the XOFF character(s) will be transmitted if Auto XON/XOFF flow control is used. It is recommended that
this value is greater than the RX Trigger Level.
TCR[7:4]: RX FIFO Resume Level
A value of 0-60 (decimal value of TCR[7:4] multiplied by 4) can be selected as the Resume Level. When the
RX FIFO is less than or equal to this value, the RTS# output will be re-asserted if Auto RTS flow control is used
or the XON character(s) will be transmitted if Auto XON/XOFF flow control is used. It is recommended that this
value is less than the RX Trigger Level.
This register replaces SPR and is accessible under the conditions listed in
to store the RX and TX FIFO trigger levels used for interrupts.
TLR[3:0]: TX FIFO Trigger Level
A value of 4-60 (decimal value of TCR[3:0] multiplied by 4) can be selected as the TX FIFO Trigger Level.
When the number of available spaces in the TX FIFO is greater than or equal to this value, a Transmit Ready
interrupt is generated. For any non-zero value, TCR[3:0] will be used as the TX FIFO Trigger Level. If
TCR[3:0] = 0x0, then the TX FIFO Trigger Level is the value selected by FCR[5:4]. See
TLR[7:4]: RX FIFO Trigger Level
A value of 4-60 (decimal value of TCR[7:4] multiplied by 4) can be selected as the RX FIFO Trigger Level.
When the number of characters received in the RX FIFO is greater than or equal to this value, a Receive Data
Ready interrupt is generated (a Receive Data Timeout interrupt is independent of the RX FIFO Trigger Level
and can be generated any time there is at least 1 byte in the RX FIFO and the RX input has been idle for the
timeout period described in
used as the RX FIFO Trigger Level. If TCR[7:4] = 0x0, then the RX FIFO Trigger Level is the value selected by
FCR[7:6]. See
These registers make-up the value of the baud rate divisor. The concatenation of the contents of DLM and
DLL is a 16-bit value is then added to DLD[3:0]/16 to achieve the fractional baud rate divisor. DLD must be
enabled via EFR bit-4 before it can be accessed.
FRACTIONAL DIVISOR” ON PAGE 11.
DLD[5:4]: Sampling Rate Select
These bits select the data sampling rate. By default, the data sampling rate is 16X. The maximum data rate will
double if the 8X mode is selected and will quadruple if the 4X mode is selected. See
4.10
4.11
4.12
4.13
Table
Scratch Pad Register (SPR) - Read/Write
Transmission Control Register (TCR) - Read/Write (requires EFR bit-4 = 1)
Trigger Level Register (TLR) - Read/Write (requires EFR bit-4 = 1)
Baud Rate Generator Registers (DLL, DLM and DLD[3:0]) - Read/Write
12.
Table
10.
“Section 2.10, Receiver” on page
SEE”PROGRAMMABLE BAUD RATE GENERATOR WITH
34
15). For any non-zero value, TCR[7:4] will be
Table
12. This 8-bit register is used
Table 14
Table
below.
10.
REV. 1.0.2