ox16pci954 ETC-unknow, ox16pci954 Datasheet - Page 37
![no-image](/images/no-image-200.jpg)
ox16pci954
Manufacturer Part Number
ox16pci954
Description
Integrated Quad Uart Interface
Manufacturer
ETC-unknow
Datasheet
1.OX16PCI954.pdf
(72 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
OX16PCI954
Manufacturer:
OXFORD
Quantity:
12 388
Company:
Part Number:
ox16pci954-TQA1G
Manufacturer:
AVAGO
Quantity:
1 400
Company:
Part Number:
ox16pci954-TQA1G
Manufacturer:
OXFORD
Quantity:
1
Part Number:
ox16pci954-TQA1G
Manufacturer:
OXFORD
Quantity:
20 000
Company:
Part Number:
ox16pci954-TQC60-A1
Manufacturer:
AD
Quantity:
556
LCR[5:3]: Parity type
The selected parity type will be generated during
transmission and checked by the receiver, which may
produce a parity error as a result. In 9-bit mode parity is
disabled and LCR[5:3] is ignored.
LCR[6]: Transmission break
logic 0
logic 1
alert the communication terminal, or send zeros in IrDA
mode.
It is the responsibility of the software driver to ensure that
the break duration is longer than the character period for it
to be recognised remotely as a break rather than data.
LCR[7]: Divisor latch enable
logic 0
logic 1
7.5.3
This register provides the status of data transfer to CPU.
LSR[0]: RHR data available
logic 0
logic 1
LSR[1]: RHR overrun error
logic 0
logic 1
LSR[2]: Received data parity error
logic 0
logic 1
Data Sheet Revision 1.3
OXFORD SEMICONDUCTOR LTD.
LCR[5:3]
Break transmission disabled.
Forces the transmitter data output SOUT low to
Access to DLL and DLM registers disabled.
Access to DLL and DLM registers enabled.
Line Status Register ‘LSR’
Table 23: LCR Parity Configuration
001
011
101
111
RHR is empty: no data available
RHR is not empty: data is available to be read.
No overrun error.
Data was received when the RHR was full. An
overrun error has occurred. The error is flagged
when the data would normally have been
transferred to the RHR.
No parity error in normal mode or 9
received data is ‘0’ in 9-bit mode.
Data has been received that did not have
correct parity in normal mode or 9
received data is ‘1’ in 9-bit mode.
xx0
Parity bit forced to 1
Parity bit forced to 0
Even parity bit
Odd parity bit
No parity bit
Parity type
th
th
bit of
bit of
The Parity error flag will be set when the data item in error
is at the top of the RHR and cleared following a read of the
LSR. In 9-bit mode LSR[2] is no longer a flag and
corresponds to the 9
LSR[3]: Received data framing error
logic 0
logic 1
This status bit is set and cleared in the same manner as
LSR[2]. When a framing error occurs, the UART will try to
re-synchronise by assuming that the error was due to
sampling the start bit of the next data item.
LSR[4]: Received break error
logic 0
logic 1
A break condition occurs when the SIN line goes low
(normally signifying a start bit) and stays low throughout
the start, data, parity and first stop bit. (Note that the SIN
line is sampled at the bit rate). One zero character with
associated break flag set will be transferred to the RHR
and the receiver will then wait until the SIN line returns
high. The LSR[4] break flag will be set when this data item
gets to the top of the RHR and it is cleared following a read
of the LSR.
LSR[5]: THR empty
logic 0
logic 1
LSR[6]: Transmitter and THR empty
logic 0
logic 1
LSR[7]: Receiver data error
logic 0
logic 1
In 450 mode LSR[7] is permanently cleared, otherwise this
bit will be set when an erroneous character is transferred
from the receiver to the RHR. It is cleared when the LSR is
read. Note that in 16C550 this bit is only cleared when
all of the erroneous data are removed from the FIFO. In
9-bit data framing mode parity is permanently disabled, so
this bit is not affected by LSR[2].
No framing error.
Data has been received with an invalid stop bit.
No receiver break error.
The receiver received a break.
Transmitter FIFO (THR) is not empty.
Transmitter FIFO (THR) is empty.
The transmitter is not idle
THR is empty and the transmitter has
completed the character in shift register and is
in idle mode. (I.e. set whenever the transmitter
shift register and the THR are both empty.)
Either there are no receiver data errors in the
FIFO or it was cleared by a read of LSR.
At least one parity error, framing error or break
indication in the FIFO.
th
bit of the received data in RHR.
OX16PCI954
Page 37