hsp50214a Intersil Corporation, hsp50214a Datasheet - Page 51
![no-image](/images/manufacturer_photos/0/3/342/intersil_corporation_sml.jpg)
hsp50214a
Manufacturer Part Number
hsp50214a
Description
Programmable Downconverter
Manufacturer
Intersil Corporation
Datasheet
1.HSP50214A.pdf
(60 pages)
POSITION
POSITION
POSITION
31-17
16-15
13-11
31-28
27-16
30-28
27-25
24-21
CONTROL WORD 17: DISCRIMINATOR FILTER CONTROL, DISCRIMINATOR DELAY (SYNCHRONIZED TO PROCCLK)
11-0
BIT
BIT
BIT
8-3
2-0
14
10
31
9
Reserved
Phase Multiplier
Discriminator Enable
Discriminator FIR
Decimation
FIR Symmetry Type
FIR Symmetry
Number of FIR Taps
Discriminator Delay
Reserved
NCO Divide
Reference Divide
Reserved
Data Source for
SEROUTA
Data Source for
SEROUTB
Number of Serial
Word Links in a
Chain
FUNCTION
FUNCTION
FUNCTION
CONTROL WORD 18: TIMING ERROR PRELOADS (SYNCHRONIZED TO PROCCLK)
CONTROL WORD 19: SERIAL OUTPUT ORDER (SYNCHRONIZED TO PROCCLK)
Reserved.
These bits program allow the phase output of the cartesian to polar converter to be multiplied
by 1, 2, 4, or 8 (modulo 2 ) to remove phase modulation before the frequency is measured.
00- No Shift on Phase Input to frequency discriminator.
01- Shift Phase Input to frequency discriminator up 1 (one bit), discarding the MSB and zero
filling the LSB.
10- Shift Phase Input to frequency discriminator up 2 (two) bits, discarding the MSB and zero
filling the LSB.
11- Shift Phase Input to frequency discriminator up 3 (three) bits, discarding the MSB and zero
filling the LSB.
0- Disable Discriminator.
1- Enable Discriminator.
The decimation can be programmed from 1 to 8, where 000 = decimate by 8; 001 = decimate
by 1; 010 = decimate by 2; 011 = decimate by 3; 100 = decimate by 4; 101 = decimate by 5; 110
= decimate by 6; and 111 - decimate by 7.
0- Odd Symmetry.
1- Even Symmetry.
0- Symmetric.
1- Asymmetric.
Number of FIR taps from 1 to 63, where 00000 is not valid (00001 = 1 tap, 00010 = 2 taps, etc.
up to 11111 = 63 taps). Bit 8 is the MSB.
where 000 represents 1 delay; 001 represents 2 delays, 010 represents 3 delays, 011 repre-
sents 4 delays, 100 represents 5 delays, 101 represents 6 delays, 110 represents 7 delays,
and 111 represents 8 delays. If ddd the decimal representation bits 2-0, then the discriminator
a transfer function H(Z) = 1-Z
Reserved.
The Re-Sampler NCO output is divided down by the value loaded into this register plus 1. Load
with a value that is one less than the desired period. Bit 27 is the MSB.
The reference clock is divided down by the value loaded into this register plus 1. Load with a
value that is one less than the desired period. Bit 27 is the MSB. A minimum preload of “I” is
required.
Reserved.
Serial Output A Source. The serial data source is selected using Table 12 (see Output Section).
Serial Output B Source. The serial data source is selected using Table 12 (see Output Section).
This parameter determines the number of SERSYNC pulses generated. It can be set from 1 to
7. If this parameter matches the number of serial words that are linked together to form a serial
output chain, then there will be a sync pulse for every word in the serial output. In applications
where a processor is receiving the serial data, it may be desirable to have a single SERSYNC
pulse for the whole serial output chain, instead of a SERSYNC for each word in the data chain.
The processor then parses out the various data words. As an example, if the I and Q are
chained together and a single SERSYNC pulse is generated for this serial output chain, no am-
biguity exists in the processor about which two data samples (one from I and one from Q) are
related.
Sets the number of delays from 1 to 8 in the discriminator. Set delay ddd to delay minus 1,
HSP50214A
51
-(ddd + 1)
.
DESCRIPTION
DESCRIPTION
DESCRIPTION