afct-57d5anpz Avago Technologies, afct-57d5anpz Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/0/85/avago_technologies_sml.jpg)
afct-57d5anpz
Manufacturer Part Number
afct-57d5anpz
Description
Digital Diagnostic Sfp Small Form Pluggable , Low Voltage 3.3 V 25km, 1310nm Dfb, 8.5/4.25/2.125 Gbd Fibre Channel Rohs Compliant Digital Diagnostic Optical Transceiver
Manufacturer
Avago Technologies
Datasheet
1.AFCT-57D5ANPZ.pdf
(18 pages)
Description,
As an enhancement to the conventional SFP interface
defined in SFF-8074i, the AFCT-57D5ANPZ is compliant
to SFF-8472 (digital diagnostic interface for optical trans-
ceivers). Using the 2-wire serial interface defined in the
SFF-8472 MSA, the AFCT-57D5ANPZ provides real time
temperature, supply voltage, laser bias current, laser
average output power and received input power. This in-
formation is in addition to conventional SFP base data. The
digital diagnostic interface also adds the ability to disable
the transmitter (TX_DISABLE), monitor for Transmitter
Faults (TX_FAULT), and monitor for Receiver Loss of Signal
(RX_LOS).
Installation
The AFCT-57D5ANPZ can be installed in any SFF-8074i
compliant Small Form Pluggable (SFP) port regardless of
host equipment operating status. The AFCT-57D5ANPZ is
hot-pluggable, allowing the module to be installed while
the host system is operating and on-line. Upon insertion,
the transceiver housing makes initial contact with the
host board SFP cage, mitigating potential damage due to
Electro-Static Discharge (ESD).
Digital Diagnostic Interface and Serial Identification
The 2-wire serial interface is based on ATMEL AT24C01A
series EEPROM protocol and signaling detail. Conventional
EEPROM memory, bytes 0-255 at memory address 0xA0,
is organized in compliance with SFF-8074i. New digital
diag n ostic information, bytes 0-255 at memory address
0xA2, is compliant to SFF-8472. The new diagnostic in-
formation provides the opportunity for Predictive Failure
Identification, Com p liance Prediction, Fault Isolation and
Component Monitoring.
Predictive Failure Identification
The AFCT-57D5ANPZ predictive failure feature allows a
host to identify potential link problems before system per-
formance is impacted. Prior identification of link problems
enables a host to service an application via “fail over” to
a redundant link or replace a suspect device, maintain-
ing system uptime in the process. For applications where
ultra-high system uptime is required, a digital SFP provides
a means to monitor two real-time laser metrics asso c iated
with observing laser degradation and predicting failure:
average laser bias current (Tx_Bias) and average laser
optical power (Tx_Power).
2
continued
Compliance Prediction
Compliance prediction is the ability to determine if an
optical transceiver is operating within its operating and
environmental requirements. AFCT-57D5ANPZ devices
provide real-time access to transceiver internal supply
voltage and temperature, allowing a host to identify
potential component compliance issues. Received optical
power is also available to assess compliance of a cable
plant and remote transmitter. When operating out of
requirements, the link cannot guarantee error free trans-
mission.
Fault Isolation
The fault isolation feature allows a host to quickly pinpoint
the location of a link failure, minimizing downtime. For
optical links, the ability to identify a fault at a local device,
remote device or cable plant is crucial to speeding service
of an installation. AFCT-57D5ANPZ real-time monitors of
Tx_Bias, Tx_Power, Vcc, Temperature and Rx_Power can be
used to assess local transceiver current operating condi-
tions. In addition, status flags Tx_Disable and Rx Loss of
Signal (LOS) are mirrored in memory and available via the
two-wire serial interface.
Component Monitoring
Component evaluation is a more casual use of the AFCT-
57D5ANPZ real-time monitors of Tx_Bias, Tx_Power,
Vcc, Temperature and Rx_Power. Potential uses are as
debugging aids for system installation and design, and
transceiver parametric evaluation for factory or field
qualification. For example, temperature per module can be
observed in high density applications to facilitate thermal
evaluation of blades, PCI cards and systems.