ak4648 AKM Semiconductor, Inc., ak4648 Datasheet - Page 81
![no-image](/images/no-image-200.jpg)
ak4648
Manufacturer Part Number
ak4648
Description
Stereo Codec With Mic/hp/spk-amp
Manufacturer
AKM Semiconductor, Inc.
Datasheet
1.AK4648.pdf
(119 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
ak4648EC-L
Manufacturer:
AKM
Quantity:
20 000
■
The AK4648 supports the fast-mode I
to (TVDD+0.3) V or less voltage.
1. WRITE Operations
Figure 60 shows the data transfer sequence for the I
HIGH to LOW transition on the SDA line while SCL is HIGH indicates a START condition (Figure 66). After the
START condition, a slave address is sent. This address is 7 bits long followed by the eighth bit that is a data direction bit
(R/W). The most significant six bits of the slave address are fixed as “001001”. The next bit is CAD0 (device address bit).
This bit identifies the specific device on the bus. The hard-wired input pin (CAD0 pin) sets these device address bits
(Figure 61). If the slave address matches that of the AK4648, the AK4648 generates an acknowledge and the operation is
executed. The master must generate the acknowledge-related clock pulse and release the SDA line (HIGH) during the
acknowledge clock pulse (Figure 67). A R/W bit value of “1” indicates that the read operation is to be executed. A “0”
indicates that the write operation is to be executed.
The second byte consists of the control register address of the AK4648. The format is MSB first, and those most
significant 2-bits are fixed to zeros (Figure 62). The data after the second byte contains control data. The format is MSB
first, 8bits (Figure 63). The AK4648 generates an acknowledge after each byte has been received. A data transfer is
always terminated by a STOP condition generated by the master. A LOW to HIGH transition on the SDA line while SCL
is HIGH defines a STOP condition (Figure 66).
The AK4648 can perform more than one byte write operation per sequence. After receiving the third byte the AK4648
generates an acknowledge and awaits the next data. The master can transmit more than one byte instead of terminating the
write cycle after the first data byte is transferred. After receiving each data packet the internal 6-bit address counter is
incremented by one, and the next data is automatically taken into the next address. If the address exceeds 27H prior to
generating a stop condition, the address counter will “roll over” to 00H and the previous data will be overwritten.
The data on the SDA line must remain stable during the HIGH period of the clock. The HIGH or LOW state of the data
line can only change when the clock signal on the SCL line is LOW (Figure 68) except for the START and STOP
conditions.
MS0625-E-01
Serial Control Interface
SDA
S
T
A
R
T
S
Slave
Address
D7
0
0
R/W="0"
Figure 60. Data Transfer Sequence at the I
A
C
K
D6
0
0
Figure 63. Byte Structure after the second byte
Sub
Address(n)
2
C-bus (max.: 400kHz). Pull-up resistors at SDA and SCL pins should be connected
(The CAD0 should match with CAD0 pin)
A5
D5
1
Figure 62. The Second Byte
Figure 61. The First Byte
C
A
K
2
C-bus mode. All commands are preceded by a START condition. A
Data(n)
A4
D4
0
- 81 -
C
A3
D3
A
K
0
Data(n+1)
2
A2
D2
C-Bus Mode
1
C
A
K
CAD0
A1
D1
C
A
K
Data(n+x)
R/W
A0
D0
C
A
K
S
T
O
P
P
[AK4648]
2007/06