am79d2251 Advanced Micro Devices, am79d2251 Datasheet - Page 8
![no-image](/images/manufacturer_photos/0/0/14/advanced_micro_devices_sml.jpg)
am79d2251
Manufacturer Part Number
am79d2251
Description
Dual Intelligent Subscriber Line Audio-processing Circuit Islac
Manufacturer
Advanced Micro Devices
Datasheet
1.AM79D2251.pdf
(35 pages)
8
CS/RST
SHB, SLB,
SPB
TSCA
VSAB1–
VSAB2
VCCA1–
VCCA2
VCCD
VREF
VHL1–
VHL2
VIN1–
VIN2
VLB1–
VLB2
VIMT1–
VIMT2,
VILG1–
VILG2
VOUT1–
VOUT2
XSB1–
XSB2
XSC
Pin
/G,
Chip Select/Reset
Battery Sense
Timeslot Control A/GCI
Mode, Time Slot
Control B
Loop voltage sense
Power Supply
Power Supply
Analog Reference
High Level D/A
TX Analog
Longitudinal
Reference
Sense
RX Analog
External Sense
Common External
Sense
Pin Name
(PCM)
(GCI)
I/O
O
O
O
O
O
I
I
I
I
I
I
I
I
For PCM backplane operation, a logic low on this pin for 15 or more DCLK cycles resets
the sequential logic in the ISLAC device into a known mode. A logic low placed on this pin
for less than 15 DCLK cycles is a chip select and enables serial data transmission into or
out of the DIO port. For GCI operation, a logic low on this pin—for 1 ms or longer—resets
the sequential logic into a known mode. See Table 2-4 in the Technical Reference for
details. 5 V tolerant.
Resistors that sense the high, low and positive battery voltages connect here. If only one
negative battery is used, connect both resistors at the supply. If the positive battery is not
used, leave the pin unconnected. These pins are current inputs whose voltage is held at
VREF.
For PCM backplane operation, TSCA is active low when PCM data is output on the DXA
pin. The outputs are open-drain and are normally inactive (high impedance). Pull-up loads
should be connected to VCCD. When GCI mode is selected, one of two GCI modes may
be selected by connecting TSCA/G to DGND or VCCD.
Connect to the VSAB pins of two ISLIC devices.
+3.3 VDC supplies to the analog sections in each of the two channels.
+3.3 VDC supply to all digital sections.
This pin provides a 1.4 V, single-ended reference to the two ISLIC devices to which the
ISLAC device is connected.
High-level loop control voltages on these pins are used to control DC-feed, internal ringing,
metering and polarity reversal for each ISLIC device.
Analog transmit signals (VTX) from each ISLIC device connect to these pins. The ISLAC
device converts these signals to digital words and processes them. After processing, they
are multiplexed into serial time slots and sent out of the DXA/DU pin.
Normally connected to VCCA internally. They supply longitudinal reference voltages to the
ISLIC devices during certain test procedures. These outputs are connected internally to
VCCA during ISLIC Active, Standby, Ringing, and Disconnect modes. During test modes,
it can be connected to the receive D/A.
The IMT and ILG pins of two ISLIC devices connect to the VIMT1–VIMT4 and VILG1–
VILG4 pins of the ISLAC chip. These pins are voltage inputs referenced to VREF. They
require external resistors connected between each pin and VREF to convert IMTn and
ILGn into voltages.
The ISLAC device extracts and processes voice data from time slots on DRA/DD serial
data port. After processing, the ISLAC device converts the voice data to analog signals
that are sent out of these pins to each respective ISLIC device.
External resistors connect here that sense an external voltage. In a linecard with external
ringing, they are used to sense the voltage at the line side of the ring-feed resistor. These
pins are current inputs whose voltage is held at VREF. An internal resistor converts currents
flowing in these pins into voltages to be sampled by the A/D.
An external resistor connects here that senses a common reference for external voltages
sensed by resistors connected to XSB1–XSB4. This pin is a current input whose voltage
is held at VREF. An internal resistor converts current flowing in this pin into a voltage to
be sampled by the A/D. This pin is intended for sensing external ringer supply voltages.
However, it can also be used to sense other test points when internal ringing is used.
Am79D2251
Description