lrs1386 Sharp Microelectronics of the Americas, lrs1386 Datasheet - Page 92
![no-image](/images/no-image-200.jpg)
lrs1386
Manufacturer Part Number
lrs1386
Description
Flash Memory
Manufacturer
Sharp Microelectronics of the Americas
Datasheet
1.LRS1386.pdf
(114 pages)
- Current page: 92 of 114
- Download datasheet (4Mb)
The two-cycle command sequence ensures that block is
not accidentally locked-down. An invalid Set Block
Lock-down Bit command sequence will result in both
status register bits SR.5 and SR.4 being set to "1" and the
operation will not be executed.
The Set Block Lock-down Bit command is available
when the power supply voltage is specified level,
independent of the voltage on V
At power-up or device reset, since no blocks are locked-
down, write the Set Block Lock-down Bit command as
necessary.
While WP# is V
not cleared. Once any block is locked-down, it cannot be
cleared until power-off or device reset.
IH
, the lock-down bits are disabled but
Appendix to Spec No.: MFM2-J13302
PP
.
FUM00701
Model No.: LRS1386
4.15 OTP Program Command
OTP program is executed by a two-cycle command
sequence. At the first cycle, command (C0H) and an
address within the OTP block (see Figure 4) is written,
followed by the second write that specifies the address
and data. After writing the command, the device outputs
the status register data when any address within the
device is selected. The WSM then takes over, controlling
the internal OTP program algorithm. The system CPU
can detect the OTP program completion by analyzing the
output data of the status register bit SR.7. Figure 13.1 and
Figure 13.2 show OTP program flowchart.
The address written at the command cycle must be the
address within the OTP block (refer to Figure 4). Writing
an address outside the OTP block will cause a OTP
program error and the status register bit SR.4 is set to "1".
Clear the status register before writing next command.
The internal WSM verify only detects errors for "1"s that
are not successfully programmed to "0"s. Check the status
register bit SR.4 at the end of OTP program. If a OTP
program error is detected, the status register should be
cleared before system software attempts corrective
actions.
For reliable OTP program operation, apply the specified
voltage on V
voltage, OTP program operations are not guaranteed. For
example, attempting an OTP program at V
causes SR.4 and SR.3 being set to "1". OTP program
operation on locked area causes SR.4 and SR.1 being set
to "1" and the operation will not be executed.
OTP program cannot be suspended through the (Page
Buffer) Program Suspend command (B0H). Even if the
(Page Buffer) Program Suspend command is written
during OTP program operation, the suspend command
will be ignored.
If an error is detected during the OTP program operation,
error bits for all status registers are set to "1". This
requires that the Clear Status Register command be
written to all partitions to clear the error bits.
Dual work operation is not available while the OTP
program mode, and the memory array data cannot be read
even if that operation has been completed. To return to the
read array mode, write the Read Array command (FFH)
to the partition’s CUI after the completion of the OTP
program operation.
CC
and V
March 2, 2001
PPH1/2
on V
PP
. In the absence of this
Rev. 2.20
PP
V
46
PPLK
Related parts for lrs1386
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![ir2403](/images/no-image3.png)
Part Number:
Description:
Transistor,bjt,array,darlington,45v V Br Ceo,400ma I C ,dip
Manufacturer:
Sharp Microelectronics of the Americas
Datasheet:
![lr38580](/images/no-image3.png)
Part Number:
Description:
Single-chip Driver K/320 K-pixel Ccds With Dual-power-supply Operation
Manufacturer:
Sharp Microelectronics of the Americas
Datasheet:
![lr38585](/images/no-image3.png)
Part Number:
Description:
Single-chip Driver K/320 Pixel Ccds With Dual-power-supply Operation
Manufacturer:
Sharp Microelectronics of the Americas
Datasheet:
![lh28f016sct-zr](/images/no-image3.png)
Part Number:
Description:
Flash Memory 16mbit 2mbitx8
Manufacturer:
Sharp Microelectronics of the Americas
Datasheet:
![pq20vz11](/images/no-image3.png)
Part Number:
Description:
Variable Output, Surface Mount Type Power-loss Voltage Regulators
Manufacturer:
Sharp Microelectronics of the Americas
Datasheet:
![pq070xh01z](/images/no-image3.png)
Part Number:
Description:
Voltage Operation Power-loss Voltage Regulator
Manufacturer:
Sharp Microelectronics of the Americas
Datasheet:
![pq070xz1hz](/images/no-image3.png)
Part Number:
Description:
Voltage Operation Power-loss Voltage Regulator
Manufacturer:
Sharp Microelectronics of the Americas
Datasheet:
![pq7vz5](/images/no-image3.png)
Part Number:
Description:
Variable Output, Compact Surface Mount Type Power-loss Voltage Regulators
Manufacturer:
Sharp Microelectronics of the Americas
Datasheet:
![lrs1331](/images/no-image3.png)
Part Number:
Description:
Stacked Chip Flash Memory Sram
Manufacturer:
Sharp Microelectronics of the Americas
Datasheet:
![lr40993](/images/no-image3.png)
Part Number:
Description:
Pulse Dialer Cmos
Manufacturer:
Sharp Microelectronics of the Americas
Datasheet:
![lr4089bn](/images/no-image3.png)
Part Number:
Description:
Tone Dialer
Manufacturer:
Sharp Microelectronics of the Americas
Datasheet:
![pc714v](/images/no-image3.png)
Part Number:
Description:
High Isolation Voltage Type, General Purpose Photocoupler
Manufacturer:
Sharp Microelectronics of the Americas
Datasheet:
![pc716v](/images/no-image3.png)
Part Number:
Description:
High Sensitivity, High Output Type Photocoupler
Manufacturer:
Sharp Microelectronics of the Americas
Datasheet:
![lr4803](/images/no-image3.png)
Part Number:
Description:
Pulse Tone Dialer
Manufacturer:
Sharp Microelectronics of the Americas
Datasheet:
![SM8503](/images/no-image3.png)
Part Number:
Description:
8-bit Single-chip Microcomputer ( Controllers For General Purpose )
Manufacturer:
Sharp Microelectronics of the Americas
Datasheet: