k4r881869m Samsung Semiconductor, Inc., k4r881869m Datasheet - Page 34

• Manufacturer Part Number: k4r881869m
• Description: 288mbit Rdram 512k X 18 Bit X 2*16 Dependent Banks Direct Rdramtm
• Manufacturer: Samsung Semiconductor, Inc.

K4R881869M
Note: In RDRAMs with protocol version 1 PVER[5:0] = 000001, the
range of the PDNX field (PDNX[2:0] in the PDNX register) may not
be large enough to specify the location of the restricted interval in
Figure 47. In this case, the effective t
no row or column packets may overlap the restricted interval. See
Figure 47 and Table 19.
IDM
15 14 13 12 11 10 9
15 14 13 12 11 10 9
0
0
Control Register: CNFGA
Control Register: INIT
SDE
VID
5
0
DIS
PVER5..0
= 000001
0
TSQ
0
TEN
0
LSR
0
PSR
0
NSR
8
8
0
S4
MVER5..0
SRP PSX
= 010000
parameter must increase and
7
7
0
6
6
0
5
0
5
0
PSX - Power Exit Select. PDN and NAP are exited with (=0) or without (=1) a device address on the
DQA5..0 pins. PDEV5 (on DQA5) selectes broadcast (1) or directed (0) exit. For a directed exit,
PDEV4..0 (on DQA4..0) is compared to DEVID4..0 to select a device.
SRP - SIO Repeater. Controls value on SIO1; SIO1=SIO0 if SRP=1, SIO1=1 if SRP=0. SRP resets
to 1.
NAP Self-Refresh. NSR=1 enables self-refresh in NAP mode. NSR can’t be set while in NAP
mode. NSR resets to 0.
PDN Self-Refresh. PSR=1 enables self-refresh in PDN mode. PSR can’t be set while in PDN mode.
PSR resets to 0.
Low Power Self-Refresh. LSR=1 enables longer self-refresh interval. The self-refresh supply
current is reduced. LSR resets to 0.
Temperature Sensing Enable. TEN=1 enables temperature sensing circuitry, permitting the TSQ bit
to be read to determine if a thermal trip point has been exceeded. TEN resets to 0.
Temperature Sensing Output. TSQ=1 when a temperature trip point has been exceeded, TSQ=0
when it has not. TSQ is available during a current control operation (see Figure 51).
RDRAM Disable. DIS=1 causes RDRAM to ignore NAP/PDN exit sequence, DIS=0 permits
normal operation. This mechanism disables an RDRAM. DIS resets to 0.
Interleaved Device Mode. IDM=1 causes 8 RDRAMs interleave read/write data, IDM=0 permits
normal operation . IDM resets to 0.
4
SDEVID4..SDEVID0
4
0
Address: 021
Address: 023
DBL
3
3
0
1
Figure 28: CNFGA Register
2
2
REFBIT2..0
0
Figure 27: INIT Register
= 101
1
1
0
0
0
0
16
16
Page 32
Read-only register.
REFBIT2..0 - Refresh Bank Bits. Specifies the number of
bank address bits used by REFA and REFP commands.
Permits multi-bank refresh in future RDRAMs.
DBL - Doubled-Bank. DBL=1 means the device uses a
doubled-bank architecture with adjacent-bank dependency.
DBL=0 means no dependency.
MVER5..0 - Manufacturer Version. Specifies the manufac-
turer identification number.
PVER5..0 - Protocol Version. Specifies the Direct Protocol
version used by this device:
0 - Reserved
1 - Version 1 protocol.
2 - Version 1 plus Interleaved Device Mode .
3 to 63 - Reserved.
Read/write register.
Reset values are undefined except as affected by SIO Reset as noted
below. SETR/CLRR Reset does not affect this register.
SDEVID5..0 - Serial Device Identification. Compared to SDEV5..0
serial address field of serial request packet for register read/write transac-
tions. This determines which RDRAM is selected for the register read or
write operation. SDEVID resets to 3f
. .
16
.
Preliminary
Direct RDRAM
Rev. 0.9 Jan. 2000
™