gl852 Genesys Logic, gl852 Datasheet - Page 16
![no-image](/images/no-image-200.jpg)
gl852
Manufacturer Part Number
gl852
Description
Usb 2.0 Mtt Hub Controller
Manufacturer
Genesys Logic
Datasheet
1.GL852.pdf
(31 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
GL852
Manufacturer:
GENESYS
Quantity:
20 000
Part Number:
gl852-MN
Manufacturer:
GENESYS
Quantity:
20 000
Company:
Part Number:
gl852-MNG02
Manufacturer:
CHRONTEL
Quantity:
430
Company:
Part Number:
gl852G
Manufacturer:
GENESYS
Quantity:
10
Part Number:
gl852G
Manufacturer:
GENESYS
Quantity:
20 000
Company:
Part Number:
gl852G-31
Manufacturer:
GENESYS
Quantity:
6 571
Company:
Part Number:
gl852G-32
Manufacturer:
ZORAN
Quantity:
107
Part Number:
gl852G-HHY12
Manufacturer:
GENESYS
Quantity:
20 000
Company:
Part Number:
gl852G-MNG03
Manufacturer:
MAXIM
Quantity:
5 637
Part Number:
gl852G-MNG03
Manufacturer:
GENESYS
Quantity:
20 000
CHAPTER 5 FUNCTION DESCRIPTION
5.1 General
©2000-2007 Genesys Logic Inc. - All rights reserved.
USPORT (upstream port) transceiver is the analog circuit that supports both full-speed and high-speed
electrical characteristics defined in chapter 7 of USB specification Revision 2.0. USPORT transceiver will
operate in full-speed electrical signaling when GL852 is plugged into a 1.1 host/hub. USPORT transceiver
will operate in high-speed electrical signaling when GL852 is plugged into a 2.0 host/hub.
GL852 contains a 40x PLL. PLL generates the clock sources for the whole chip. The generated clocks are
proven quite accurate that help in generating high speed signal without jitter.
This module implements hub (micro)frame timer. The (micro)frame timer is derived from the hub’s local
clock and is synchronized to the host (micro)frame period by the host generated Start of (micro)frame
(SOF). FRTIMER keeps tracking the host’s SOF such that GL852 is always safely synchronized to the host.
The functionality of FRTIMER is described in section 11.2 of USB Specification Revision 2.0.
operates at 6MIPS of 12Mhz clock to decode the USB command issued from host and then prepares the
data to respond to the host. In addition, C can handle GPIO (general purpose I/O) settings and reading
content of EEPROM to support high flexibility for customers of different configurations of hub. These
configurations include self/bus power mode setting, individual/gang mode setting, downstream port number
setting, device removable/non-removable setting, and PID/VID setting.
UTMI handles the low level USB protocol and signaling. It’s designed based on the Intel’s UTMI
specification 1.01. The major functions of UTMI logic are to handle the data and clock recovery, NRZI
encoding/decoding, Bit stuffing /de-stuffing, supporting USB 2.0 test modes, and serial/parallel conversion.
USPORT implements the upstream port logic defined in section 11.6 of USB specification Revision 2.0. It
mainly manipulates traffics in the upstream direction. The main functions include the state machines of
Receiver and Transmitter, interfaces between UTMI and SIE, and traffic control to/from the REPEATER
and TT.
SIE handles the USB protocol defined in chapter 8 of USB specification Revision 2.0. It co-works with
C to play the role of the hub kernel. The main functions of SIE include the state machine of USB protocol
flow, CRC check, PID error check, and timeout check. Unlike USB 1.1, bit stuffing/de-stuffing is
implemented in UTMI, not in SIE.
Control/Status register is the interface register between hardware and firmware. This register contains the
information necessary to control endpoint0 and endpoint1 pipelines. Through the firmware based
architecture, GL852 possesses higher flexibility to control the USB protocol easily and correctly.
Repeater logic implements the control logic defined in section 11.4 and section 11.7 of USB specification
Revision 2.0. REPEATER controls the traffic flow when upstream port and downstream port are signaling
in the same speed. In addition, REPEATER will generate internal resume signal whenever a wakeup event
is issued under the situation that hub is globally suspended.
5.1.1 USPORT Transceiver
5.1.2 PLL (Phase Lock Loop)
5.1.3 FRTIMER
5.1.4 µC
5.1.5 UTMI (USB 2.0 Transceiver Macrocell Interface)
5.1.6 USPORT logic
5.1.7 SIE (Serial Interface Engine)
5.1.8 Control/Status register
5.1.9 REPEATER
C is the micro-processor unit of GL852. It is an 8-bit RISC processor with 2K ROM and 64 bytes RAM. It
GL852 USB 2.0 MTT HUB Controller
Page 16
μ