CS8140YDW24 CHERRY [Cherry Semiconductor Corporation], CS8140YDW24 Datasheet - Page 11

• Manufacturer Part Number: CS8140YDW24
• Description: 5V, 500mA Linear Regulator with ENABLE, , and Watchdog RESET
• Manufacturer: CHERRY [Cherry Semiconductor Corporation]

Step 3: Increase the ESR of the capacitor from zero using
the decade box and vary the load current until oscillations
appear. Record the values of load current and ESR that
cause the greatest oscillation. This represents the worst
case load conditions for the regulator at low temperature.
Step 4: Maintain the worst case load conditions set in step
3 and vary the input voltage until the oscillations increase.
This point represents the worst case input voltage condi-
tions.
Step 5: If the capacitor is adequate, repeat steps 3 and 4
with the next smaller valued capacitor. A smaller capacitor
will usually cost less and occupy less board space. If the
output oscillates within the range of expected operating
conditions, repeat steps 3 and 4 with the next larger stan-
dard capacitor value.
Step 6: Test the load transient response by switching in
various loads at several frequencies to simulate its real
working environment. Vary the ESR to reduce ringing.
Step 7: Remove the unit from the environmental chamber
and heat the IC with a heat gun. Vary the load current as
instructed in step 5 to test for any oscillations.
Once the minimum capacitor value with the maximum
ESR is found, a safety factor should be added to allow for
the tolerance of the capacitor and any variations in regula-
tor performance. Most good quality aluminum electrolytic
capacitors have a tolerance of +/- 20% so the minimum
value found should be increased by at least 50% to allow
for this tolerance plus the variation which will occur at
low temperatures. The ESR of the capacitor should be less
than 50% of the maximum allowable ESR found in step 3
above.
The maximum power dissipation for a single output regu-
lator (Figure 9) is:
where:
V
V
I
tion, and
I
I
P
OUT(max)
Q
OUT(max)
D(max)
IN(max)
OUT(min)
is the quiescent current the regulator consumes at
=
is the maximum input voltage,
.
is the maximum output current for the applica-
in a Single Output Linear Regulator
{
is the minimum output voltage,
V
IN(max)
Calculating Power Dissipation
- V
OUT(min)
}
I
OUT(max)
+ V
IN(max)
Application Notes: continued
I
Q
(1)
11
Figure 9: Single output regulator with key performance parameters
labeled.
Once the value of P
sible value of R
The value of R
the package section of the data sheet. Those packages
with R
keep the die temperature below 150¡C.
In some cases, none of the packages will be sufficient to
dissipate the heat generated by the IC, and an external
heatsink will be required.
A heatsink effectively increases the surface area of the
package to improve the flow of heat away from the IC and
into the surrounding air.
Each material in the heat flow path between the IC and the
outside environment will have a thermal resistance. Like
series electrical resistances, these resistances are summed
to determine the value of R
where:
R
R
are functions of the package type, heatsink and the inter-
face between them. These values appear in heatsink data
sheets of heatsink manufacturers.
QJC
QJA
R
R
R
QJC
QCS
QSA
, it too is a function of package type. R
appears in the package section of the data sheet. Like
QJA
= the junctionÐtoÐcase thermal resistance,
= the caseÐtoÐheatsink thermal resistance, and
= the heatsinkÐtoÐambient thermal resistance.
's less than the calculated value in equation 2 will
V
IN
QJA
R
QJA
I
IN
QJA
can then be compared with those in
can be calculated:
R
D(max)
= R
QJA
QJC
=
Heatsinks
}
Control
Features
is known, the maximum permis-
Regulator
150¡C - T
+ R
QJA
Smart
QCS
:
P
D
I
Q
+ R
A
QSA
I
OUT
QCS
and R
V
OUT
QSA
(2)
(3)