MT48LC128M4A2_07 MICRON [Micron Technology], MT48LC128M4A2_07 Datasheet - Page 30
MT48LC128M4A2_07
Manufacturer Part Number
MT48LC128M4A2_07
Description
512Mb x4, x8, x16 SDRAM
Manufacturer
MICRON [Micron Technology]
Datasheet
1.MT48LC128M4A2_07.pdf
(68 pages)
- Current page: 30 of 68
- Download datasheet (3Mb)
Figure 20:
Figure 21:
PDF: 09005aef809bf8f3/Source: 09005aef80818a4a
512MbSDRAM.fm - Rev. L 10/07 EN
Random WRITE Cycles
WRITE-to-READ
Note:
Note:
COMMAND
COMMAND
Data for a fixed-length WRITE burst may be followed by, or truncated with, a
PRECHARGE command to the same bank (provided that auto precharge was not acti-
vated), and a full-page WRITE burst may be truncated with a PRECHARGE command to
the same bank. The PRECHARGE command should be issued
which the last desired input data element is registered. The auto precharge mode
requires a
truncating a WRITE burst, the DQM signal must be used to mask input data for the clock
edge prior to, and the clock edge coincident with, the PRECHARGE command. An
example is shown in Figure 22 on page 31. Data n + 1 is either the last of a burst of two or
the last desired of a longer burst. Following the PRECHARGE command, a subsequent
command to the same bank cannot be issued until
issued coincident with the first coincident second clock (Figure 22 on page 31). In the
case of a fixed-length burst being executed to completion, a PRECHARGE command
issued at the optimum time (as described above) provides the same operation that
would result from the same fixed-length burst with auto precharge. The disadvantage of
ADDRESS
ADDRESS
Each WRITE command may be to any bank. DQM is LOW.
The WRITE or READ commands may be to any bank. DQM is LOW.
CLK
DQ
CLK
DQ
t
WR of at least one clock plus time, regardless of frequency. In addition, when
BANK,
WRITE
COL n
D
WRITE
BANK,
T0
COL n
n
IN
D
T0
n
IN
Transitioning Data
WRITE
BANK,
COL a
T1
D
n + 1
a
NOP
IN
D
T1
IN
30
BANK,
WRITE
COL x
T2
D
BANK,
x
COL b
READ
IN
T2
Transitioning Data
Don’t Care
WRITE
BANK,
COL m
Micron Technology, Inc., reserves the right to change products or specifications without notice.
T3
D
m
T3
IN
NOP
NOP
D
T4
OUT
b
t
RP is met. The precharge can be
512Mb: x4, x8, x16 SDRAM
Don’t Care
NOP
b + 1
T5
D
OUT
t
WR after the clock edge at
©2000 Micron Technology, Inc. All rights reserved.
Operations
Related parts for MT48LC128M4A2_07
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
FPM DRAM
Manufacturer:
MICRON [Micron Technology]
Datasheet:
Part Number:
Description:
EDO DRAM
Manufacturer:
MICRON [Micron Technology]
Datasheet:
Part Number:
Description:
DRAM MODULE
Manufacturer:
MICRON [Micron Technology]
Datasheet:
Part Number:
Description:
576Mb: x18, x36 RLDRAM 3
Manufacturer:
MICRON [Micron Technology]
Datasheet:
Part Number:
Description:
Mobile Double Data Rate (DDR) SDRAM
Manufacturer:
MICRON [Micron Technology]
Datasheet:
Part Number:
Description:
DOUBLE DATA RATE (DDR) SDRAM
Manufacturer:
MICRON [Micron Technology]
Datasheet:
Part Number:
Description:
DOUBLE DATA RATE DDR SDRAM
Manufacturer:
MICRON [Micron Technology]
Datasheet:
Part Number:
Description:
Double Data Rate (DDR) SDRAM
Manufacturer:
MICRON [Micron Technology]
Datasheet:
Part Number:
Description:
DOUBLE DATA RATE DDR SDRAM
Manufacturer:
MICRON [Micron Technology]
Datasheet:
Part Number:
Description:
DDR2 SDRAM
Manufacturer:
MICRON [Micron Technology]
Datasheet:
Part Number:
Description:
256Mb: 16 Meg x 16, 8 Meg x 32 Mobile SDRAM
Manufacturer:
MICRON [Micron Technology]
Datasheet:
Part Number:
Description:
512Mb: 32 Meg x 16, 16 Meg x 32 Mobile SDRAM
Manufacturer:
MICRON [Micron Technology]
Datasheet:
Part Number:
Description:
SYNCHRONOUS DRAM
Manufacturer:
MICRON [Micron Technology]
Datasheet:
Part Number:
Description:
SYNCHRONOUS DRAM
Manufacturer:
MICRON [Micron Technology]
Datasheet:
Part Number:
Description:
SYNCHRONOUS DRAM
Manufacturer:
MICRON [Micron Technology]
Datasheet: