AD53040 AD [Analog Devices], AD53040 Datasheet - Page 3

• Manufacturer Part Number: AD53040
• Description: Ultrahigh Speed Pin Driver with Inhibit Mode
• Manufacturer: AD [Analog Devices]

ABSOLUTE MAXIMUM RATINGS
Power Supply Voltage
Inputs
Outputs
V
Environmental
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection.
Although the AD53040 features proprietary ESD protection circuitry, permanent damage may
occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD
precautions are recommended to avoid performance degradation or loss of functionality.
REV. B
Parameter
DYNAMIC PERFORMANCE, DRIVE
DYNAMIC PERFORMANCE, INHIBIT
POWER SUPPLIES
NOTES
Connecting or shorting the decoupling capacitors to ground will result in the destruction of the device.
Specifications subject to change without notice.
OUT
+V
–V
+V
DATA, DATA, INH, INH . . . . . . . . . . . . . . . . +5 V, –3 V
DATA to DATA, INH to INH . . . . . . . . . . . . . . . . . . 3 V
V
V
V
V
V
THERM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +13 V, 0 V
Operating Temperature (Junction) . . . . . . . . . . . . . . +175 C
Storage Temperature . . . . . . . . . . . . . . . . –65 C to +150 C
Lead Temperature (Soldering, 10 sec)
(V
Delay Time, Active to Inhibit
Delay Time, Inhibit to Active
I/O Spike
Output Capacitance
Total Supply Range
Positive Supply
Negative Supply
Positive Supply Current
Negative Supply Current
Total Power Dissipation
Temperature Sensor Gain Factor
H
H
OUT
LDCPL
HDCPL
H
Minimum Pulsewidth
S
, V
S
S
to V
Range in Inhibit Mode
and V
to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –8 V
3 V Swing
5 V Swing
Toggle Rate
to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +13 V
to –V
L
Short Circuit Duration . . . . . . . . . . . . . . . . Indefinite
to GND . . . . . . . . . . . . . . . . . . . . . . . . . +9 V, –4 V
L
. . . . . Do Not Connect Except for Capacitor to V
. . . . . Do Not Connect Except for Capacitor to V
L
S
) (Continued)
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +11 V, 0 V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +20 V
1
3
. . . . . . . . . . +260 C
Min
2
2
CC
EE
2
Typ
1.7
2.6
500
<200
5
19
+12
–7
1.15
1.0
–3–
NOTES
1
2
3
Model
AD53040KRP 20-Lead Power SOIC Tube, 38 Pieces
Stresses above those listed under Absolute Maximum Ratings may cause perma-
Output short circuit protection is guaranteed as long as proper heat sinking is
To ensure lead coplanarity ( 0.002 inches) and solderability, handling with bare
nent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Absolute maximum limits apply
individually, not in combination. Exposure to absolute maximum rating conditions
for extended periods may affect device reliability.
employed to ensure compliance with the operating temperature limits.
hands should be avoided and the device should be stored in environments at 24 C
5 C (75 F
Max
5
5
75
75
1.43
10 F) with relative humidity not to exceed 65%.
Package
Description
Units
ns
ns
MHz
ns
ns
mV, p-p
pF
V
V
V
mA
mA
W
A/K
ORDERING GUIDE
Test Conditions
4.0 ns Input, 10%/90% Output,
V
6.0 ns Input, 10%/90% Output,
V
V
V
Measured at 50%, V
V
Measured at 50%, V
V
V
Driver Inhibited
R
L
L
L
OUT
L
L
H
LOAD
= 0 V, V
= 0 V, V
= –1.8 V, V
= –2 V
= –2 V
= 0 V, V
WARNING!
> 600 mV p-p
Shipment Method,
Quantity Per
Shipping Container Option
= 10 K, V
H
H
L
= 3 V
= 5 V
= 0 V
H
ESD SENSITIVE DEVICE
= –0.8 V,
SOURCE
H
H
= +2 V,
= +2 V,
AD53040
= +12 V
Package
RP-20