LPC47M112_07 SMSC [SMSC Corporation], LPC47M112_07 Datasheet - Page 95
![no-image](/images/no-image-200.jpg)
LPC47M112_07
Manufacturer Part Number
LPC47M112_07
Description
Enhanced Super I/O Controller with LPC Interface
Manufacturer
SMSC [SMSC Corporation]
Datasheet
1.LPC47M112_07.pdf
(204 pages)
- Current page: 95 of 204
- Download datasheet (2Mb)
Enhanced Super I/O Controller with LPC Interface
Datasheet
OPERATION
Mode Switching/Software Control
Software will execute P1284 negotiation and all operation prior to a data transfer phase under programmed I/O control
(mode 000 or 001). Hardware provides an automatic control line handshake, moving data between the FIFO and the
ECP port only in the data transfer phase (modes 011 or 010).
Setting the mode to 011 or 010 will cause the hardware to initiate data transfer.
If the port is in mode 000 or 001 it may switch to any other mode. If the port is not in mode 000 or 001 it can only be
switched into mode 000 or 001. The direction can only be changed in mode 001.
Once in an extended forward mode the software should wait for the FIFO to be empty before switching back to mode
000 or 001. In this case all control signals will be deasserted before the mode switch. In an ecp reverse mode the
software waits for all the data to be read from the FIFO before changing back to mode 000 or 001. Since the automatic
hardware ecp reverse handshake only cares about the state of the FIFO it may have acquired extra data which will be
discarded. It may in fact be in the middle of a transfer when the mode is changed back to 000 or 001. In this case the
port will deassert nAutoFd independent of the state of the transfer. The design shall not cause glitches on the
handshake signals if the software meets the constraints above.
ECP Operation
Prior to ECP operation the Host must negotiate on the parallel port to determine if the peripheral supports the ECP
protocol. This is a somewhat complex negotiation carried out under program control in mode 000.
After negotiation, it is necessary to initialize some of the port bits. The following are required:
Set Direction = 0, enabling the drivers.
Set strobe = 0, causing the nStrobe signal to default to the deasserted state.
Set autoFd = 0, causing the nAutoFd signal to default to the deasserted state.
Set mode = 011 (ECP Mode)
ECP address/RLE bytes or data bytes may be sent automatically by writing the ecpAFifo or ecpDFifo respectively.
Note that all FIFO data transfers are byte wide and byte aligned. Address/RLE transfers are byte-wide and only allowed
in the forward direction.
The host may switch directions by first switching to mode = 001, negotiating for the forward or reverse channel, setting
direction to 1 or 0, then setting mode = 011. When direction is 1 the hardware shall handshake for each ECP read data
byte and attempt to fill the FIFO. Bytes may then be read from the ecpDFifo as long as it is not empty.
ECP transfers may also be accomplished (albeit slowly) by handshaking individual bytes under program control in mode
= 001, or 000.
Termination from ECP Mode
Termination from ECP Mode is similar to the termination from Nibble/Byte Modes. The host is permitted to terminate
from ECP Mode only in specific well-defined states. The termination can only be executed while the bus is in the forward
direction. To terminate while the channel is in the reverse direction, it must first be transitioned into the forward direction.
SMSC DS – LPC47M112
IRQ SELECTED
All Others
15
14
11
10
9
7
5
Table 44B
CONFIG REG B
BITS 5:3
110
101
100
011
010
001
111
000
DATASHEET
Page 95
SELECTED
All Others
DMA
3
2
1
Table 44C
CONFIG REG B
BITS 2:0
011
010
001
000
Rev. 02-16-07
Related parts for LPC47M112_07
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
![LAN83C183-JD](/images/no-image3.png)
Part Number:
Description:
FAST ETHERNET PHYSICAL LAYER DEVICE
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37N769TQFP](/images/no-image3.png)
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
![LPC47M102S-MC](/images/no-image3.png)
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
![LPC47N267-MN](/images/no-image3.png)
Part Number:
Description:
357-036-542-201 CARDEDGE 36POS DL .156 BLK LOPRO
Manufacturer:
SMSC Corporation
Datasheet:
![USB20H04-JD](/images/no-image3.png)
Part Number:
Description:
4-PORT USB2.0 HUB CONTROLLER
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37M602](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37B777](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37C672](/images/no-image3.png)
Part Number:
Description:
FDC37C672ENHANCED SUPER I/O CONTROLLER WITH FAST IR
Manufacturer:
SMSC Corporation
Datasheet:
![COM90C66LJP](/images/no-image3.png)
Part Number:
Description:
COM90C66LJPARCNET Controller/Transceiver with AT Interface and On-Chip RAM
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37N869TQFP](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![USB97C100QFP](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![LPC47N227-MN](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![FDC37N869](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet:
![LAN91C94](/images/no-image3.png)
Part Number:
Description:
Manufacturer:
SMSC Corporation
Datasheet: