ISL6313 INTERSIL [Intersil Corporation], ISL6313 Datasheet - Page 33

• Manufacturer Part Number: ISL6313
• Description: Two-Phase Buck PWM Controller with Integrated MOSFET Drivers for Intel VR11 and AMD Applications
• Manufacturer: INTERSIL [Intersil Corporation]

Thin Quad Flat No-Lead Plastic Package (TQFN)
Thin Micro Lead Frame Plastic Package (TMLFP)
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
SEATING PLANE
(DATUM A)
INDEX
AREA
AREA
(DATUM B)
INDEX
AREA
6
6
A
NX L
C
1
2
3
8
3
2
1
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
N
TOP VIEW
N
D
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
5
D2
2
For information regarding Intersil Corporation and its products, see www.intersil.com
NX b
D/2
(Nd-1)Xe
BOTTOM VIEW
SECTION "C-C"
SIDE VIEW
D2
REF.
NX b
33
e
2X
0.15
5
N
C
0.10
A1
7
A
NX k
E2/2
A3
E/2
M C
8
A1
E2
B
E
A
2X
A
7
B
0.15
(Ne-1)Xe
/ /
REF.
0.08
0.10 C
C
B
8
C
ISL6313
L36.6x6
36 LEAD THIN QUAD FLAT NO-LEAD PLASTIC PACKAGE
(COMPLIANT TO JEDEC MO-220WJJD-1 ISSUE C)
NOTES:
1. Dimensioning and tolerancing conform to ASME Y14.5m-1994.
2. N is the number of terminals.
3. Nd and Ne refer to the number of terminals on each D and E.
4. All dimensions are in millimeters. Angles are in degrees.
5. Dimension b applies to the metallized terminal and is measured
6. The configuration of the pin #1 identifier is optional, but must be
7. Dimensions D2 and E2 are for the exposed pads which provide
8. Nominal dimensions are provided to assist with PCB Land Pattern
SYMBOL
between 0.15mm and 0.30mm from the terminal tip.
located within the zone indicated. The pin #1 identifier may be
either a mold or mark feature.
improved electrical and thermal performance.
Design efforts, see Intersil Technical Brief TB389.
A1
A3
D2
E1
E2
Nd
Ne
A
D
E
N
b
e
k
L
0.70
0.18
3.80
3.80
0.20
0.45
MIN
-
MILLIMETERS
NOMINAL
6.00 BSC
6.00 BSC
5.75 BSC
0.20 REF
0.50 BSC
0.75
0.25
3.95
3.95
0.55
36
9
9
-
-
MAX
0.80
0.05
0.30
4.05
4.05
0.65
-
Rev. 2 04/06
March 5, 2007
NOTES
FN6448.0
5, 8
7, 8
7, 8
9
8
2
3
3
-
-
-
-
-
-