STTS752E STMICROELECTRONICS [STMicroelectronics], STTS752E Datasheet
STTS752E
Related parts for STTS752E
STTS752E Summary of contents
Page 1
Digital temperature sensor and thermal watchdog Features ■ Measures temperatures from –55°C to +125°C (–67°F to +257°F) – ±2°C Accuracy from –25°C to +100°C (max) ■ Low operating current: 75µA (typ) ■ No external components required 2 ■ 2-wire I ...
Page 2
Contents 1 Summary description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 3
Stop data transfer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 4
List of tables Table 1. Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 5
List of figures Figure 1. Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ...
Page 6
Summary description The STTS75 is a high-precision CMOS (Digital) temperature sensor IC with a Delta-Sigma analog-to-digital (ADC) converter and page 7 targeted for general applications such as personal computers, system thermal management, electronics equipment, ...
Page 7
The measured temperature value is compared with a temperature limit (which is stored in the 16-bit (T ) READ/WRITE register), and the hysteresis temperature (which is stored in OS the 16-bit (T ) READ/WRITE register). If the measured value exceeds ...
Page 8
Figure 2. Connections (SO8, TSSOP8) 1. SDA and OS/INT are open drain. Note: See Pin descriptions on page 9 Figure 3. Functional block diagram Temperature Sensor and Analog-to-Digital Converter (ADC 8/38 SDA ...
Page 9
Pin descriptions See Figure 1 on page 7 to this device. 1.3.1 SDA (open drain) This is the Serial Data Input/Output pin for the 2-wire serial communication port. 1.3.2 SCL This is the Serial Clock Input pin for the ...
Page 10
Operation After each temperature measurement and analog-to-digital conversion, the STTS75 stores the temperature as a 16-bit two’s complement number in the 2-byte temperature register. The most significant Bit (S, Bit 15) indicates if the temperature is positive or negative: ...
Page 11
Applications information STTS75 digital Temperature Sensors are optimal for thermal management and thermal protection applications. They require no external components for operations except for pull- up resistors on SCL, SDA, and OS/INT outputs. A 0.1µF bypass capacitor is recommended. ...
Page 12
Thermal alarm function The STTS75 thermal alarm function provides user-programmable thermostat capability and allows the STTS75 to function as a standalone thermostat without using the serial interface. The OS/INT output is the alarm output. This signal is an open ...
Page 13
Interrupt mode In Interrupt mode, the OS/INT output first becomes active when the measured temperature exceeds the T value a consecutive number of times equal to the FT value in the OS Configuration register. Once activated, the OS/INT can ...
Page 14
Fault tolerance For both Comparator and Interrupt modes, the alarm “fault tolerance” setting plays a role in determining when the OS/INT output will be activated. Fault tolerance refers to the number of consecutive times an error condition must be ...
Page 15
Temperature data format Table 4 shows the relationship between the output digital data and the external temperature for 12-bit resolution. Temperature data for Temperature, T 11-bit, and 12-bit depending upon the resolution bits RC1, RC0 (Bits 6 and 5) ...
Page 16
Functional description The STTS75 registers have unique pointer designations which are defined in page 16. Whenever any READ/WRITE operation to the STTS75 register is desired, the user must “point” to the device register to be accessed. All of these ...
Page 17
Configuration register The Configuration register is used to store the device settings such as Device Operation mode, OS/INT Operation mode, OS/INT Polarity, and OS/INT Fault Queue. The Configuration register allows the user to program various options such as conversion ...
Page 18
Temperature register The Temperature Register is a two-byte (16-bit) “Read only” register (see page 18). Digital temperatures from the ADC are stored in the Temperature Register in two’s complement format, and the contents of this register are updated each ...
Page 19
Hysteresis temperature register (T T Register is a two-byte (16-bit) READ/WRITE register that stores the user- HYS programmable lower trip-point temperature for the thermal alarm in two’s complement format (see Table 10). This register defaults to 75°C at power-up ...
Page 20
Serial interface Writing to and reading from the STTS75 registers is accomplished via the two-wire serial interface protocol which requires that one device on the bus initiates and controls all READ and WRITE operations. This device is called the ...
Page 21
Data valid The state of the data line represents valid data when after a start condition, the data line is stable for the duration of the high period of the clock signal. The data on the line may be ...
Page 22
Acknowledge Each byte of eight bits is followed by one Acknowledge Bit. This Acknowledge Bit is a low level put on the bus by the receiver whereas the master generates an extra acknowledge related clock pulse (see obliged to ...
Page 23
READ mode In this mode the master reads the STTS75 slave after setting the slave address (see Figure 8). Following the WRITE mode Control Bit (R/W=0) and the Acknowledge Bit, the word address 'An' is written to the on-chip ...
Page 24
Figure 9. Typical 2-byte READ from preset pointer location (e.g. temp - Start Address Byte by Master Figure 10. Typical pointer set followed by an immediate READ for 2-byte register (e.g. ...
Page 25
WRITE mode In this mode the master transmitter transmits to the STTS75 slave receiver. Bus protocol is shown in Figure 12. Following the START condition and slave address, a logic '0' (R placed on the bus ...
Page 26
Figure 14. T and Start Address Byte by Master Most Significant Data Byte 26/38 WRITE HYS ...
Page 27
Typical operating characteristics Figure 15. Temperature variation vs. voltage 140 120 100 –20 –40 – Voltage (V) –20 0.5 85 110 125 5 6 AI12258 27/38 ...
Page 28
Maximum rating Stressing the device above the rating listed in the “Absolute Maximum Ratings” table may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above ...
Page 29
DC and AC parameters This section summarizes the operating measurement conditions, and the DC and AC characteristics of the device. The parameters in the DC and AC characteristics Tables that follow, are derived from tests performed under the Measurement ...
Page 30
Table 14. DC and AC characteristics Sym Description V Supply voltage DD V supply current, DD active temperature conversions supply current, DD communication only Standby supply current, I DD1 serial port inactive Accuracy for corresponding range 2.7V ...
Page 31
Figure 16. Bus timing requirements sequence SDA tBUF tHD:STA SCL P S Table 15. AC characteristics Sym f SCL clock frequency SCL t Time the bus must be free before a new transmission can start BUF t SDA and SCL ...
Page 32
Package mechanical data In order to meet environmental requirements, ST offers these devices in ECOPACK packages. These packages have a Lead-free second level interconnect. The category of second Level Interconnect is marked on the package and on the inner ...
Page 33
Figure 17. SO8 – 8-lead plastic small package outline A2 Note: Drawing is not to scale. Table 16. SO8 – 8-lead plastic small outline package mechanical data Sym Typ ccc D 4.90 E 6.00 E1 ...
Page 34
Figure 18. MSOP8 (TSSOP8) – 8-lead, thin shrink small package (3mm x 3mm) outline A ccc Note: Drawing is not to scale. Table 17. MSOP8 (TSSOP8) – 8-lead, thin shrink small package (3mm x 3mm) outline mechanical data Sym Typ ...
Page 35
Part numbering Table 18. Ordering information scheme Example: Device type STTS75 Package M = SO8 DS = MSOP8 (TSSOP8) Temperature range 2 = –55 to 125°C Shipping method F = ECOPACK package, Tape & Reel E = ECOPACK package, ...
Page 36
Package marking information Figure 19. Device topside marking information (SO8) 1. Traceability codes E = Additional information P = Plant code Y = Year WW = Work Week Figure 20. Device topside marking information (MSOP8/TSSOP8) 1. Traceability codes P ...
Page 37
Revision history Table 19. Revision history Date 14-Jun-2006 22-Jan-2007 01-Mar-2007 18-Apr-2007 09-May-2007 16-May-2007 06-Jun-2007 Revision 1 Initial release. Update features (cover page), DC and AC characteristics 2 (Table 14), package mecanical information Table 16, Figure 18, Table Update cover ...
Page 38
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any ...