PIC24FJ32GB002-E/ML MICROCHIP [Microchip Technology], PIC24FJ32GB002-E/ML Datasheet - Page 64

• Manufacturer Part Number: PIC24FJ32GB002-E/ML
• Description: 28/44-Pin, 16-Bit, Flash Microcontrollers with USB On-The-Go (OTG) and nanoWatt XLP Technology
• Manufacturer: MICROCHIP [Microchip Technology]

PIC24FJ64GB004 FAMILY
REGISTER 6-1:
DS39940D-page 64
bit 15
bit 7
Legend:
R = Readable bit
-n = Value at POR
bit 15
bit 14
bit 13-11
bit 10
bit 9
bit 8
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
Note 1:
R/W-0, HS
R/W-0, HS
TRAPR
EXTR
2:
All of the Reset status bits may be set or cleared in software. Setting one of these bits in software does not
cause a device Reset.
If the FWDTEN Configuration bit is ‘1’ (unprogrammed), the WDT is always enabled, regardless of the
SWDTEN bit setting.
TRAPR: Trap Reset Flag bit
1 = A Trap Conflict Reset has occurred
0 = A Trap Conflict Reset has not occurred
IOPUWR: Illegal Opcode or Uninitialized W Access Reset Flag bit
1 = An illegal opcode detection, an illegal address mode or uninitialized W register used as an Address
0 = An illegal opcode or uninitialized W Reset has not occurred
Unimplemented: Read as ‘0’
DPSLP: Deep Sleep Mode Flag bit
1 = Deep Sleep has occurred
0 = Deep Sleep has not occurred
CM: Configuration Word Mismatch Reset Flag bit
1 = A Configuration Word Mismatch Reset has occurred
0 = A Configuration Word Mismatch Reset has not occurred
PMSLP: Program Memory Power During Sleep bit
1 = Program memory bias voltage remains powered during Sleep
0 = Program memory bias voltage is powered down during Sleep and the voltage regulator enters Standby
EXTR: External Reset (MCLR) Pin bit
1 = A Master Clear (pin) Reset has occurred
0 = A Master Clear (pin) Reset has not occurred
SWR: Software Reset (Instruction) Flag bit
1 = A RESET instruction has been executed
0 = A RESET instruction has not been executed
SWDTEN: Software Enable/Disable of WDT bit
1 = WDT is enabled
0 = WDT is disabled
WDTO: Watchdog Timer Time-out Flag bit
1 = WDT time-out has occurred
0 = WDT time-out has not occurred
SLEEP: Wake From Sleep Flag bit
1 = Device has been in Sleep mode
0 = Device has not been in Sleep mode
IDLE: Wake-up From Idle Flag bit
1 = Device has been in Idle mode
0 = Device has not been in Idle mode
R/W-0, HS
R/W-0, HS
IOPUWR
SWR
Pointer caused a Reset
mode
RCON: RESET CONTROL REGISTER
CO = Clearable Only bit
W = Writable bit
‘1’ = Bit is set
SWDTEN
R/W-0
U-0
—
(2)
R/W-0, HS
WDTO
U-0
—
Preliminary
HS = Hardware Settable bit
U = Unimplemented bit, read as ‘0’
‘0’ = Bit is cleared
R/W-0, HS
(2)
SLEEP
U-0
—
(1)
R/CO-0, HS
R/W-0, HS
DPSLP
IDLE
 2010 Microchip Technology Inc.
x = Bit is unknown
R/W-0, HS
R/W-1, HS
BOR
CM
R/W-1, HS
PMSLP
R/W-0
POR
bit 8
bit 0