AT32UC3B0512-A2UES ATMEL [ATMEL Corporation], AT32UC3B0512-A2UES Datasheet - Page 68
AT32UC3B0512-A2UES
Manufacturer Part Number
AT32UC3B0512-A2UES
Description
32-bit AVR Microcontroller
Manufacturer
ATMEL [ATMEL Corporation]
Datasheet
1.AT32UC3B0512-A2UES.pdf
(91 pages)
- Current page: 68 of 91
- Download datasheet (2Mb)
12.1.2.4
12.1.2.5
12.1.2.6
12.1.2.7
SSC
USB
ADC
PDCA
1. Additional delay on TD output
2. TF output is not correct
3. Frame Synchro and Frame Synchro Data are delayed by one clock cycle.
1. For isochronous pipe, the INTFRQ is irrelevant
1. Sleep Mode activation needs additional A to D conversion
1. Wrong PDCA behavior when using two PDCA channels with the same PID
If the OSC0 is enabled in crystal mode when entering a sleep mode where the OSC0 is dis-
abled, this will lead to an increased power consumption in VDDIO.
Fix/Workaround
Disable the OSC0 through the Power Manager (PM) before going to any sleep mode where
the OSC0 is disabled, or pull down or up XIN0 and XOUT0 with 1Mohm resistor.
A delay from 2 to 3 system clock cycles is added to TD output when:
TCMR.START = Receive Start,
TCMR.STTDLY = more than ZERO,
RCMR.START = Start on falling edge / Start on Rising edge / Start on any edge,
RFMR.FSOS = None (input).
Fix/Workaround
None.
TF output is not correct (at least emitted one serial clock cycle later than expected) when:
TFMR.FSOS = Driven Low during data transfer/ Driven High during data transfer
TCMR.START = Receive start
RFMR.FSOS = None (Input)
RCMR.START = any on RF (edge/level)
Fix/Workaround
None.
The frame synchro and the frame synchro data are delayed from 1 SSC_CLOCK when:
Clock is CKDIV
The START is selected on either a frame synchro edge or a level,
Frame synchro data is enabled,
Transmit clock is gated on output (through CKO field).
Fix/Workaround
Transmit or receive CLOCK must not be gated (by the mean of CKO field) whenSTART con-
dition is performed on a generated frame synchro.
IN and OUT tokens are sent every 1 ms (Full Speed).
Fix/Workaround
For longer polling time, the software must freeze the pipe for the desired period in order to
prevent any "extra" token.
If the ADC sleep mode is activated when the ADC is idle the ADC will not enter sleep mode
before after the next AD conversion.
Fix/Workaround
Activate the sleep mode in the mode register and then perform an AD conversion.
Related parts for AT32UC3B0512-A2UES
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Atmel CryptoMemory
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
Atmel CryptoMemory
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
Atmel CryptoMemory, 16Kbit
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontrollers
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 64K/128K/256K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 16/32/64/128K Bytes In-System Programmable Flash
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
8-bit Atmel Microcontroller with 16/32/64K Bytes In-System Programmable Programmable
Manufacturer:
ATMEL [ATMEL Corporation]
Datasheet:
Part Number:
Description:
INTERVAL AND WIPE/WASH WIPER CONTROL IC WITH DELAY
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Low-Voltage Voice-Switched IC for Hands-Free Operation
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
MONOLITHIC INTEGRATED FEATUREPHONE CIRCUIT
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
AM-FM Receiver IC U4255BM-M
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Monolithic Integrated Feature Phone Circuit
Manufacturer:
ATMEL Corporation
Datasheet:
Part Number:
Description:
Multistandard Video-IF and Quasi Parallel Sound Processing
Manufacturer:
ATMEL Corporation
Datasheet: