M306V0ME-107FP MITSUBISHI [Mitsubishi Electric Semiconductor], M306V0ME-107FP Datasheet - Page 166

• Manufacturer Part Number: M306V0ME-107FP
• Description: SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
• Manufacturer: MITSUBISHI [Mitsubishi Electric Semiconductor]

166
Note: In the OSDL mode, 1.5T
Fig 2.16.5 Triple layer OSD
Table 2.16.2 Mixing layer 1 and layer 2
Display mode
Pre-divide ratio
Dot size
Horizontal display start position
Vertical display start position
Parameter
2.16.1 Triple Layer OSD
Three built-in layers of display screens accommodate triple display of channels, volume, etc., closed
caption, and sprite displays within layers 1 to 3.
The layer to be displayed in each block is selected by bit 0 or 1 of the OSD control register 2 for each
display mode (refer to Figure 2.16.7). Layer 3 always displays the sprite display.
When the layer 1 block and the layer 2 block overlay, the screen is composed with layer mixing by bit
6 or 7 of the OSD control register 1, as shown in Figure 2.16.5. Layer 3 always takes display priority of
layers 1 and 2.
Notes 1: When mixing layer 1 and layer 2, note Table 2.16.2.
2: OUT2 is always ORed, regardless of values of bits 6, 7 of the OSD control register 1. And
Layer 3
besides, even when OUT2 (layer 1 and layer 2) overlaps with SPRITE display (layer 3),
OUT2 is output without masking.
Block
Sprite
C
size cannot be used.
Layer 2
When dot size is 2Tc
and that of layer 2 as follows.
•2Tc
•3Tc
Block 9
Block 10
Block 15
Block 16
1T
C
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER
1 to
CC, OSD, CDOSD mode
(OSD, CDOSD mode)
1T
1H, 1T
2H: 2H units
3H: 3H units
C
1,
3 (OSD, CDOSD mode)
Block in Layer 1
3T
(CC mode)
1/2H, 1T
C
Arbitrary
C
Block 1
Block 2
Block 7
Block 8
2 (CC mode)
Layer 1
1/2H, 2T
3H
C
2H or 2Tc
1H
C
2H,
R, G, B of layer 1/layer 2
OUT2 of layer 1/layer 2
• Same size as layer 1
•1.5T
3H, set difference between vertical display position of layer 1
Layer 1/layer 2
As this time, vertical dot size is the same as layer 1.
Note : When layer 1/layer 2 and SPRITE display
2 AND layer 1’s horizontal dot size = 1T
Pre-divide ratio =
C
can be selected only when: layer 1’s pre-divide ratio =
overlay each other, only OUT2 in layer 1/layer 2
is output.
Arbitrary
1T
1T
SPRITE
C
C
A
1/2H
and ON-SCREEN DISPLAY CONTROLLER
1H
Same as layer 1 (See note)
Same position as layer 1
OSD, CDOSD mode
MITSUBISHI MICROCOMPUTERS
1
M306V0ME-XXXFP
Block in Layer 2
1T
C
1T
SPRITE
(except transparent)
Pre-divide ratio =
C
1H, 1.5T
M306V0EEFP
1/2H, 1.5T
C
A'
.
C
1H (See note)
C
1/2H
2
Rev. 1.0