M306V0ME-107FP MITSUBISHI [Mitsubishi Electric Semiconductor], M306V0ME-107FP Datasheet - Page 225
M306V0ME-107FP
Manufacturer Part Number
M306V0ME-107FP
Description
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER and ON-SCREEN DISPLAY CONTROLLER
Manufacturer
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet
1.M306V0ME-107FP.pdf
(256 pages)
- Current page: 225 of 256
- Download datasheet (3Mb)
Rev. 1.0
3. USAGE PRECAUTION
3.1 Timer A (timer mode)
3.2 Timer A (event counter mode)
3.3 Timer A (one-shot timer mode)
3.4 Timer A (pulse width modulation mode)
(1) Reading the timer Ai register while a count is in progress allows reading, with arbitrary timing, the
(1) Reading the timer Ai register while a count is in progress allows reading, with arbitrary timing, the
(2) When stop counting in free run type, set timer again.
(1) The timer Ai interrupt request bit becomes “1” if setting operation mode of the timer in compliance
(2) Setting the count start flag to “0” while PWM pulses are being output causes the counter to stop
(1) Setting the count start flag to “0” while a count is in progress causes as follows:
(2) The timer Ai interrupt request bit goes to “1” if the timer's operation mode is set using any of the
value of the counter. Reading the timer Ai register with the reload timing gets “FFFF
the timer Ai register after setting a value in the timer Ai register with a count halted but before the
counter starts counting gets a proper value.
value of the counter. Reading the timer Ai register with the reload timing gets “FFFF
flow or “0000
register with a count halted but before the counter starts counting gets a proper value.
• The counter stops counting and a content of reload register is reloaded.
• The TA
• The interrupt request generated and the timer Ai interrupt request bit goes to “1”.
following procedures:
• Selecting one-shot timer mode after reset.
• Changing operation mode from timer mode to one-shot timer mode.
• Changing operation mode from event counter mode to one-shot timer mode.
Therefore, to use timer Ai interrupt (interrupt request bit), set timer Ai interrupt request bit to “0”
after the above listed changes have been made.
with any of the following procedures:
• Selecting PWM mode after reset.
• Changing operation mode from timer mode to PWM mode.
• Changing operation mode from event counter mode to PWM mode.
Therefore, to use timer Ai interrupt (interrupt request bit), set timer Ai interrupt request bit to “0”
after the above listed changes have been made.
counting. If the TA
and the timer Ai interrupt request bit goes to “1”. If the TAiOUT pin is outputting an “L” level in this
instance, the level does not change, and the timer Ai interrupt request bit does not becomes “1”.
iOUT
16
pin outputs “L” level.
” by overflow. Reading the timer Ai register after setting a value in the timer Ai
iOUT
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER with CLOSED CAPTION DECODER
pin is outputting an “H” level in this instance, the output level goes to “L”,
and ON-SCREEN DISPLAY CONTROLLER
MITSUBISHI MICROCOMPUTERS
M306V0ME-XXXFP
M306V0EEFP
16
16
” by under-
”. Reading
225
Related parts for M306V0ME-107FP
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
128 x 8-BIT x 2 MAIL-BOX
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
PROGRAMMABLE BUFFERED I/0 EXPANDER
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
ELECTRONIC SOUND CONTROL WITH ELECTRONIC VOLUME FOR MULTIPLE SOURCES
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
2CH 4 MODE PRESET EQUALIZER
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SERIAL DATA CONTROL DUAL ELECTRONIC VOLUME
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SCREEN CHARACTER and PATTERN DISPLAY CONTROLLERS?????
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
M51996P
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER??
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
MITSUBISHI SEMICONDUCTOR (TRIAC) MEDIUM POWER USE INSULATED TYPE, PLANAR PASSIVATION TYPE
Manufacturer:
Mitsubishi Electric Semiconductor
Part Number:
Description:
MITSUBISHI SEMICONDUCTOR (TRIAC) LOW POWER USE GLASS PASSIVATION TYPE
Manufacturer:
Mitsubishi Electric Semiconductor
Part Number:
Description:
SINGLE-CHIP 4-BIT CMOS MICROCOMPUTER for VOLTAGE SYNTHESIZER with ON-SCREEN DISPLAY CONTROLLER?
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SINGLE-CHIP 8-BIT CMOS MICROCOMPUTER
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet:
Part Number:
Description:
SINGLE CHIP 8 BIT CMOS MICROCOMPUTER
Manufacturer:
MITSUBISHI [Mitsubishi Electric Semiconductor]
Datasheet: