STM1403ARM-Q6F STMICROELECTRONICS [STMicroelectronics], STM1403ARM-Q6F Datasheet - Page 2
![no-image](/images/no-image-200.jpg)
STM1403ARM-Q6F
Manufacturer Part Number
STM1403ARM-Q6F
Description
3V FIPS-140 Security Supervisor with Battery Switchover
Manufacturer
STMICROELECTRONICS [STMicroelectronics]
Datasheet
1.STM1403ARM-Q6F.pdf
(9 pages)
STM1403
SUMMARY DESCRIPTION
The STM1403 family of security supervisors are a
low power family of intrusion (tamper) detection
chips targeted at manufacturers of POS terminals
and other systems, to enable them to meet phys-
ical and/or environmental intrusion monitoring
requirements as mandated by various standards,
such as Federal Information Processing Stan-
dards (FIPS) Pub 140 entitled “Security Require-
ments for Cryptographic Modules,” published by
the National Institute of Standards and Technolo-
gy, U.S. Department of Commerce), EMVCo, ISO,
ZKA, and VISA PED. STM1403 supports target
levels 3 and lower
The
Switchover, RST Output (Open Drain), Manual
(Push-button) Reset Input (MR), Power-fail Com-
parator (PFI/PFO), Physical and/or Environmental
Tamper Detect/Security Alarm, and Battery Low
Voltage Detect features.
The STM1403A also offers a V
option on pin 9. On the STM1403B/C, this pin is
V
Figure 2. Logic Diagram
Note: 1. V
2/9
V
TP 1 (NH)
TPU
CCSW
2. Normal Mode: Low when V
3. SAL, RST, PFO, and BLD are Open Drain.
(internally switched V
MR
PFI
STM1403
V
(2)
REF
CC
and High when V
only for STM1403A; V
BLD
(NL)
TP 2
(3)
includes
V
STM1403
(NH)
TP 3
V
TPU
REF
or
OUT
(1)
is internally switched to battery.
(NL)
V
TP 4
CC
TPU
OUT
BAT
Automatic
or V
REF
for STM1403B/C.
is internally switched to
V
V
CC
SS
BAT
(1.237V) as an
).
AI09682
V
RST
PFO
SAL
Battery
OUT
(3)
(3)
(3)
V
The STM1403 is available in three versions, corre-
sponding to three modes of the V
Voltage Out), when the SAL (Security Alarm) is as-
serted (active-low) upon tamper detection:
STM1403A. V
when SAL is driven low (activated).
STM1403B. V
driven low (activated).
STM1403C. V
is activated (may be used when V
directly to the V
holds the cryptographic codes).
All variants (see
compatible and available in a security-friendly, low
profile, 16-pin QFN package.
Table 2. Signal Names
Note: See
Vccsw
MR
PFI
TP
V
RST
PFO
SAL
BLD
V
V
V
V
V
OUT
OUT
REF
TPU
BAT
CC
SS
1
(2)
(2)
- TP
(2)
details.
(2)
1. Normal Mode: Low when V
2. SAL, RST, PFO, and BLD are Open Drain.
3. V
(3)
(3)
Pin Modes
(1)
V
CC
REF
4
PIN DESCRIPTIONS, page 9
and High when V
only for STM1403A; V
OUT
OUT
OUT
CC
Table 1., Device
is driven to Ground when SAL
V
Manual (Push-button) Reset Input
Power-fail Input
Independent Physical Tamper
Detect Pins 1 through 4
Supply Voltage Output
Active-low Reset Output
Power-fail Output
Security Alarm Output
Battery Low Voltage Detect
1.237V Reference Voltage
Tamper Pull-up
(V
Back-up Supply Voltage
Supply Voltage
Ground
is set to High-Z when SAL is
pin of the external SRAM that
stays ON (at V
CC
CC
OUT
Switch Output
or V
is internally switched to battery.
BAT
TPU
OUT
)
for STM1403B/C.
of the full datasheet for
is internally switched to
OUT
Options) are pin-
OUT
CC
is connected
pin (Supply
or V
BAT
)