A29L004UW-70 AMICC [AMIC Technology], A29L004UW-70 Datasheet - Page 5

• Manufacturer Part Number: A29L004UW-70
• Description: 512K X 8 Bit CMOS 3.0 Volt-only, Boot Sector Flash Memory
• Manufacturer: AMICC [AMIC Technology]

Absolute Maximum Ratings*
Storage Temperature Plastic Packages . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .0 C to + 70 C
Ambient Temperature with Power Applied . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 C to + 70 C
Voltage with Respect to Ground
VCC (Note 1) . . . . . . . . . . . . . . . . . . . . . . . -0.5V to +4.0V
A9,
All other pins (Note 1) . . . . . . . . . . . . -0.5V to VCC + 0.5V
Output Short Circuit Current (Note 3) . . . . . . . . .
Notes:
1. Minimum DC voltage on input or I/O pins is -0.5V. During
2. Minimum DC input voltage on A9,
3. No more than one output is shorted at a time. Duration
Device Bus Operations
Legend:
L = Logic Low = V
Notes:
1. See the “Sector Protection/Unprotection” section and Temporary Sector Unprotect for more information.
2. This function is not available on 32-pin PLCC & (s)TSOP packages.
PRELIMINARY
This section describes the requirements and use of the
device bus operations, which are initiated through the
internal command register. The command register itself
does not occupy any addressable memory location. The
register is composed of latches that store the commands,
along with the address and data information needed to
Write
Read
CMOS Standby
Output Disable
Hardware Reset
Sector Protect
(See Note 2)
Sector Unprotect
(See Note 2)
Temporary Sector
Unprotect
voltage transitions, input or I/O pins may undershoot
VSS to -2.0V for periods of up to 20ns. Maximum DC
voltage on input and I/O pins is VCC +0.5V. During
voltage transitions, input or I/O pins may overshoot to
VCC +2.0V for periods up to 20ns.
0.5V. During voltage transitions, A9,
may overshoot VSS to -2.0V for periods of up to 20ns.
Maximum DC input voltage on A9 is +12.5V which may
overshoot to 14.0V for periods up to 20ns. ( RESET is
N/A on 32-pin PLCC & (s)TSOP)
of the short circuit should not be greater than one
second.
OE
Operation
& RESET (Note 2) . . . . . . . . . . . . -0.5 to +12.5V
IL
, H = Logic High = V
(October, 2002, Version 0.0)
VCC
CE
X
X
L
L
L
L
L
0.3 V
IH
OE
, V
OE
Table 1. A29L004 Device Bus Operations
H
X
H
X
H
H
X
L
ID
and RESET is
OE
= 12.0 0.5V, X = Don't Care, D
and RESET
WE
H
H
X
X
X
L
L
L
200mA
(N/A 32-pin PLCC, (s)TSOP)
-
5
execute the command. The contents of the register serve
as inputs to the internal state machine. The state machine
outputs dictate the function of the device. The appropriate
device bus operations table lists the inputs and control
levels required, and the resulting output. The following
subsections describe each of these operations in further
detail.
VCC
*Comments
Stresses above those listed under "Absolute Maximum
Ratings" may cause permanent damage to this device.
These are stress ratings only. Functional operation of
this device at these or any other conditions above
those indicated in the operational sections of these
specification is not implied or intended. Exposure to
the absolute maximum rating conditions for extended
periods may affect device reliability.
Operating Ranges
Commercial (C) Devices
Ambient Temperature (T
VCC Supply Voltages
VCC for all devices . . . . . . . . . . . . . . . . . . +2.7V to +3.6V
Operating ranges define those limits between which the
functionally of the device is guaranteed.
RESET
V
V
V
H
H
H
L
ID
ID
ID
0.3 V
IN
= Data In, D
OUT
A6=H, A1=H, A0=L
A6=L, A1=H, A0=L
Sector Address,
Sector Address,
AMIC Technology, Corp.
A
= Data Out, A
) . . . . . . . . . . . . . . 0 C to +70 C
A0 – A18
A
A
A
X
X
X
A29L004 Series
IN
IN
IN
IN
= Address In
I/O
High-Z
High-Z
High-Z
D
0
D
D
D
D
OUT
- I/O
IN
IN
IN
IN
7