PEF2091 Siemens Semiconductor Group, PEF2091 Datasheet - Page 173
PEF2091
Manufacturer Part Number
PEF2091
Description
ICs for Communications(ISDN Echocancellation Circuit)
Manufacturer
Siemens Semiconductor Group
Datasheet
1.PEF2091.pdf
(298 pages)
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
PEF2091
Manufacturer:
Infineon
Quantity:
15
Company:
Part Number:
PEF2091
Manufacturer:
SIEMENS
Quantity:
5 510
Company:
Part Number:
PEF2091
Manufacturer:
SMC
Quantity:
5 510
Company:
Part Number:
PEF2091-N
Manufacturer:
INFINEON
Quantity:
2 100
Company:
Part Number:
PEF2091-NV3.3
Manufacturer:
DIODES
Quantity:
1 700
Part Number:
PEF2091N-V3.3
Manufacturer:
SIEMENS/西门子
Quantity:
20 000
- Current page: 173 of 298
- Download datasheet (3Mb)
Wait for SF AL
This state is entered in the case of an analog loop-back and allows the Receiver to
update the AGC, to recover the timing phase, and to update the EQ-coefficients. Signal
SN3 is sent instead of signal SN2 in the "Wait-for-SF" state.
4.4.4
State Diagram
The LT-RP- and NT-RP-state diagrams are subsets of the related diagrams of LT and
NT modes so the meaning of events and states are mostly identical. All differences
caused by special requirements of the implementation of the repeater modes are listed
below.
– ACT-, UOA-, SAI- and DEA-bits are completely controlled via the MON-2-messages,
– To enable the deactivation of the first section in case of an erroneous situation in the
– The MON-2-message is accepted and stored at any time except during reset (pin or
Note 47:
Semiconductor Group
so they are not referenced as outputs in the state diagrams.
second section of the U-interface, a new C/I-channel code is introduced. DU (0011)
leads to the deactivation of the NT-RP passing to "Receive Reset".
C/I-channel command).
mode. This implies that the C/I indications ARL and AIL are not issued upon
reception of the EOC command LBBD from upstream in the states
’Synchronized’, Transparent and ’ERROR S/T’ of the NT-RP state diagram
(see "State Transition Diagram NT-Repeater Mode", page 175). For handling
EOC commands in repeater mode, see "EOC Addressing Management",
page 257.
In non standard applications of the NT repeater mode the C/I indications ARL
and AIL will be issued if the EOC Auto mode is being used and if the EOC
command LBBD has been received from upstream.
State Machine in Repeater Modes
In repeater applications it is recommended to use the EOC Transparent
173
Operational Description
Data Sheet 01.99
PEB 2091
PEF 2091
Related parts for PEF2091
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Intel 80C32 - Siemens SAB-C501, Nearest Equivalent Replacement
Manufacturer:
Siemens Semiconductor Group
Part Number:
Description:
IGBT MODULE
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
SIMOPAC Module (Power module Single switch N channel Enhancement mode)
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
(BSMxxx) TRANSISTOR
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
SIMOPAC Module (Power module Single switch N channel Enhancement mode)
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
main ratings
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
ICs for Consumer Electronics
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
Video and Sound IF with V & S SCART
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
Multistandard Sound IF
Manufacturer:
Siemens Semiconductor Group
Datasheet:
Part Number:
Description:
MULTISTANDARD AM FM SOUND IF IC
Manufacturer:
Siemens Semiconductor Group
Datasheet: