EDS11-113D FUJI [Fuji Electric], EDS11-113D Datasheet - Page 2

• Manufacturer Part Number: EDS11-113D
• Description: FC SERIES MANUAL LOADER(CONTINUOUS OUTPUT TYPE)
• Manufacturer: FUJI [Fuji Electric]

2
SPECIFICATIONS
1. Input signal
(1) Process value input signal:
Voltage input
signal
Current input
signal
Thermocouple
input
Resistance
bulb input
Note *: FS: Full scale
(2) Analog input signal: 1 point
External MV
input signal
(3) Digital input signal: 2 point
Manual mode
command
Valve position
commend
2. Output signal
(1) Manipulated output signal: 1 point
Current output
(2) Analog output signal: 2 points
Compensated process
value signal
Control output
(3) Digital output signal: 4 points
Fault output
High alarm output
Low alarm output
3. Indication, setting, operating functions
(1) Bargraph indication
Indication method
No. of segments
Range
Resolution
Scale length
Indication mode
(2) Operation mode indication
Indicating method:
Manual mode output
PNB3
Ml
Ml
AI 1
I
I
I
SMV
EXS
+
0
–
+
–
One input selectable from the following.
LED (red and green)
1 to 5V DC
4 to 20mA DC
Types
J: 0 to 600 C
K: 0 to 1200 C
E: 0 to 800 C
R: 0 to 1600 C
Pt100
–50 to 500 C
Red: M, HM
Green: A
1 to 5V DC Input resistance, 1M
4 to 20mA DC
KPV
MV
FLT
M
H
L
(photo-coupler
insulation)
Contact input
PV indicator
LED (red)
101 + 2
0 to 100%, linear
1 %/FS
100mm
0 to 100% bargraph indication,
0 to 100% reverse bar graph indication,
0 to 100% dot indication, –50 to +50%
deviation indication
Open-collector out-
put (photo-coupler
insulation)
(0 C)
1 to 5V DC
Allow. error 0.2%/FS
Input resistance 1M
or more
Allowable error
Allowable error
+0.2%/FS*
24V 2V DC can be supplied
to transmitter in case of AC
power supply (approx. 35mA
max)
10mV DC span or more;
cold junction compensation
comprised
Allowable error
50 C span or more
Allowable error
0.2%/FS*
0.5%/FS*
0.5%/FS*
Allow. Ioad resistance,
600
Allow error 0 2%/FS
ON 0V, OFF 24V
( input current, approx.
11mA/24V DC)
Output resistance, 1
less
Allow error 0 2%/FS
or less
MV indicator
LED (red)
51 + 2
0 to 100%, linear
2 %/FS
50mm
Output rating,
3 0 V x 0 . 1 A D C ,
max.
or more
or
(3) Numerical indication, setting
Indication method:
Indication contents:
Setting method: By using F/S ,
(4) Operating functions
Manual operating method:
Auto operating method:
Hard manual operating method:
(5) Operation mode selection
By using A/M pushbutton and HM switch on front of the panel
M
M
A
A
A
A
(6) Alarm function
High/low alarm can be set in industrial values for process
value input signal.
4. Power failure processing functions
Power failure detection:
During power failure:
Power failure recovery time:
5. Self-diagnosis functions
Process value input signal abnormality:
Note: * Balanceless bumpless by setting tracking speed
HM selection
HM selection
M selection*
HM selection
HM selection*
M selection
LED (red), name in 3 digits + number in 5
digits (negative sign included)
Process variable (industrial value), high/
low alarm, limiter value, etc.
Indication contents are selected with F/S ,
on front panel
By using of
front of the panel
Setting speed, approx. 40 sec/FS
Simultaneous press of
8 sec/FS
By using external MV input signal
Output limiter:
Tracking speed setting range; 0 to 900
sec/FS
By using control knob on front panel of
HMV unit
Control output holds at power failure
detection.
Operating parameters backed up by
capacitor when power failure occurs
within 5 minutes.
Initial value of control output is stored in
non-volatile memory (lasts for 10 years
expected at ambient temperature of 50 C
or less).
Initial or continuous start mode can be set
for power failure within 5 minutes.
Recovery from power failure lasting
longer than 5 minutes is done by initial.
Note: Control mode at initialization can be
FLT indicator lights and FLT contact
output turns "ON"
High limit setting range, –25 to 125%
Low limit setting range, –25 to 125%
,
registered
M: Manual mode or A: Auto mode
keys on front panel.
Balance bumpless
Balanceless bumpless
,
,
,
,
pushbuttons on
button, approx.
, ST keys